Please check my Youtube channel:
Please Check My Youyube channel :
https://www.youtube.com/watch?v=nGydAGGLcDo
Hello Guys I know so many of you have the same question when you start using cohesive element in abaqus. This section is a bit confusing E/Enn does not mean dividing. It simply means Young modulus...
07 August 2019 7,846 4 View
Hello As it can be seen from below figure my simulation and experiments results are really close to each other. I just do not understand why load increases suddenly after 4 mm displacement in...
31 December 2018 4,231 0 View
I have flexible adhesive the Maximum stress is around 2.5 MPa and strain is around 150%. When we want to calculate Young modulus for normal material we normally take values from 0.05% to 0.25%...
31 December 2018 7,959 0 View
I want to plot load vs Displacement. For this I'm using the "sum" command in abaqus to add the magnitude of all the reaction forces on the fixed nodes but the load value is very low, i.e.,less...
07 August 2017 4,408 11 View
Hello I have problem with unit system in abaqus. I have already checked tables and discussions about this subject in internet and I am confused and looking for Numerical example. Could you please...
06 July 2017 9,461 5 View
I am currently working on adhesive joint. I want to do experimental test (DCB and ENF) to find cohesive zone information for my simulation. I am using Ansys software could anyone simply explain...
03 April 2017 817 0 View
For example in tensile test displacement rate is 0.76 mm/min. My question is that how can i give exactly the same rate in ANSYS. Regards Armin
02 March 2017 3,210 0 View
Please check my page for tutorials
31 December 2016 4,323 4 View
Hello I want to analysis composite under in-plane loading. I have 2 problems 1- I could not choose proper boundary condition. When I applied boundary condition solved by R Jones my results is not...
02 March 2015 5,139 5 View
I am experimenting with cancer and non-cancer cells in a 12-well plate for 4 days with a seeding density 1*10^4/well, however, I noticed that the control group growth rate slows down on D3. Should...
07 August 2024 2,283 2 View
Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...
07 August 2024 8,106 4 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
A Markov-like Model for Patient Progression" Markov Chain Monte Carlo (MCMC) Markov Chain Monte Carlo (MCMC) is a powerful computational technique used to draw samples from a probability...
05 August 2024 10,079 0 View
Hi everyone, If you have written or come across any papers where Generalised Linear Mixed Models are used to examine intervention (e.g., in mental health) efficacy, could you please share the...
04 August 2024 4,130 4 View
I have been performing short phagocytosis experiments using 96-round bottom, tissue culture treated, well plates (Falcon, 353077). I culture the cells with the phagocytic cargo for 2-4hrs, wash...
04 August 2024 5,228 4 View
Details of the Analysis. Static Analysis Composite Layup Continuum Shell Elements FRP Material (Elastic and Hashin Damage)
03 August 2024 8,538 4 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View
In my study, I intend to infect PBMCs with SARS-CoV-2. After that, I will analyze NK cells by flow cytometry to see if their phenotype changes or if they show degranulation. After the infection, I...
01 August 2024 4,403 4 View
Dear researchers, Today, we found this object in one of the wells of a 96wp culture plate. The plate contained MEC-1 cells and GelTrex. I am quite curious what this is (because it's not cells). Do...
01 August 2024 2,250 2 View