What is the meaning of E/Enn in traction in abaqus?

Hello Guys I know so many of you have the same question when you start using cohesive element in abaqus. This section is a bit confusing E/Enn does not mean dividing. It simply means Young modulus...

07 August 2019 7,379 4 View

How to calculate Young modulus for Flexible adhesive?

I have flexible adhesive the Maximum stress is around 2.5 MPa and strain is around 150%. When we want to calculate Young modulus for normal material we normally take values from 0.05% to 0.25%...

31 December 2018 7,849 0 View

How to calculate total load in a displacement control analysis in abaqus?

07 August 2017 4,242 11 View

ABQUS unit system

Hello I have problem with unit system in abaqus. I have already checked tables and discussions about this subject in internet and I am confused and looking for Numerical example. Could you please...

06 July 2017 9,344 5 View

Can anyone simply explain me how can i get Cohesive zone parameters by doing experimental test?

I am currently working on adhesive joint. I want to do experimental test (DCB and ENF) to find cohesive zone information for my simulation. I am using Ansys software could anyone simply explain...

03 April 2017 710 0 View

How can I apply displacement rate (mm/time) in Ansys?

02 March 2017 3,017 0 View

Are You looking for a Full ANSYS ACP tutorials?

31 December 2016 4,218 4 View

Tutorial: How to model Progressive Damage on Composite Plate?

09 October 2016 2,468 1 View

Anyone familiar with buckling of simply supported laminated plates under in-plane loading?

02 March 2015 5,044 5 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Which is a lucid standard comprehensive book to guide on psychological scale construction and its standardization?

02 March 2021 7,082 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How to choose ANN number of hidden layers and nodes?

Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...

01 March 2021 6,200 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

How could I take into consideration the weights of observation in a system of seemingly unrelated regressions (SUR) in rstudio?

I build a model of 4 regression equations (probit and OLS) in R studio. I need to take the weights of observations into consideration. While it is simple to do so for every regression equation,...

27 February 2021 1,233 1 View

Can random sampling have inclusion criteria?

As random sampling means that everyone in the population have an equal chance to be chosen, can it have inclusion criteria? My research participants have been chosen based on the inclusion...

26 February 2021 6,905 10 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

Why am I getting 'Infinity' and 'NaN' in my mixed-mode energy release values?

Hi everyone, I am currently running a mixed-mode simulation of a DCB using a user-defined cohesive zone model (UEL), however, the results I am getting don't make sense. I used the same UEL for...

24 February 2021 4,157 1 View