What is the meaning of E/Enn in traction in abaqus?

Hello Guys I know so many of you have the same question when you start using cohesive element in abaqus. This section is a bit confusing E/Enn does not mean dividing. It simply means Young modulus...

07 August 2019 7,379 4 View

Why my Load-Displacement curve from simulation is not correct?

Hello As it can be seen from below figure my simulation and experiments results are really close to each other. I just do not understand why load increases suddenly after 4 mm displacement in...

31 December 2018 4,136 0 View

How to calculate total load in a displacement control analysis in abaqus?

07 August 2017 4,242 11 View

ABQUS unit system

Hello I have problem with unit system in abaqus. I have already checked tables and discussions about this subject in internet and I am confused and looking for Numerical example. Could you please...

06 July 2017 9,344 5 View

Can anyone simply explain me how can i get Cohesive zone parameters by doing experimental test?

I am currently working on adhesive joint. I want to do experimental test (DCB and ENF) to find cohesive zone information for my simulation. I am using Ansys software could anyone simply explain...

03 April 2017 710 0 View

How can I apply displacement rate (mm/time) in Ansys?

02 March 2017 3,017 0 View

Are You looking for a Full ANSYS ACP tutorials?

31 December 2016 4,218 4 View

Tutorial: How to model Progressive Damage on Composite Plate?

09 October 2016 2,468 1 View

Anyone familiar with buckling of simply supported laminated plates under in-plane loading?

02 March 2015 5,044 5 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How relevant is Mini slump cone?

for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...

26 February 2021 3,668 1 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View

How to reduce residual stresses in MD simulation?

I am working on a preparation of representative polymeric structures of some popular polymers, such as polyimide or PTFE for MD simulation, during which a single nitrogen or oxygen atom will be...

24 February 2021 8,105 3 View

Suggestions for occupational stress surveys?

I am currently writing a masters thesis on reasons for occupational stress in the early childhood classroom, and want to include a short survey assessing participants work-related stress levels. I...

24 February 2021 8,678 2 View

The most suitable method to calculate the stress intensity factor in the presence of contact between the crack lips?

I'm trying to study cracked structures under a compressive load taking into account contact between the crack lips. I would like to know if the method of extrapolation by displacement remains...

21 February 2021 8,694 4 View

How to assign two different material/section properties in Abaqus(UMAT)?

Hi everyone, I am conducting a non-linear multi-layer pavement structure analysis which is a stress-dependent. So far, I am able to define the nonlinearity for one soil layer for its resilient...

11 February 2021 9,607 3 View

Are there any exception like work hardening in metals elastic limit due to dynamic loading?

The samples made out of spring steel are taken from same lot. The specimens were shaped following heating to forging temperature - Forming- Hardening -Tempering methods. After storage of almost 6...

11 February 2021 952 6 View

Why are we measuring gel content of NBR latex? Does gel content related to the amount of cross-linked in a polymer?

Hi good day to everyone! I am actually studying the gel content of synthetic latex. Refer to ASTM 3616, gel content is measure of insoluble rubbers in the chosen solvent. So, I just would like to...

07 February 2021 605 4 View