27 July 2020 7 9K Report

Any recommended URL or idea , that explains how to read encoder via Arduino IDE and then use these readings in MATLAB simulation to be used as a feedback compared with the desired speed and direction of a DC Motor Encoder in a control loop

Many thanks for sharing information in this regards

More Yazen Hudhaifa Shakir Alnema's questions See All
DNA migrated backwards, and 3 tracking dyes moved as expected. Why did that happen?

Full disclosure: This was the third run using the same gel and running buffer (I added distilled water to compensate for evaporation). I know you're not supposed to reuse running buffer this much,...

08 January 2021 6,544 6 View

Can chloroform be effectively stabilized with isopropanol? And why does ethanol stabilization usually only involve 1% by mass?

The oxidation of chloroform is dangerous because it results in phosgene formation under exposure to UV light. Along with the minimization of UV exposure, this reaction is usually prevented with 1%...

30 December 2020 3,356 3 View

Fuzzy Logic Controller warning ?

Dear All when simulating a feedback control system with Fuzzy controller in MATLAB Simulink for a tank level get this warning in run mode : ''input 2 expects a value in range [-4 4], but has a...

08 August 2020 4,568 8 View

Similar questions and discussions
fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close