What is the difference between ASTM D3410 and D695?

Hany Mostafa Fergany @Hany-Mostafa-Fergany

31 August 2023 0 8K Report

These standards are for testing Compression samples in fiberglass, and my question is when to use each.

Badges
Science topic

More Hany Mostafa Fergany's questions See All

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Do you know any references for analyzing stochastic fiber orientaion composites ?

Hello everyone I am looking for one or some books for propertes and behaviors of stochastic fibre orientation composites. unfotunately I could not find any suitable reference for thias by...

04 August 2024 3,461 3 View

What is the recommended safe distance between drilled holes in fiberglass, and which standard governs the drilling process?

Material : Fiberglass sheet thickness : 3mm

03 June 2024 6,255 0 View

What is the simplest way to introduce a heterostructure??

The best definition of heterostructure.

16 May 2024 9,848 1 View

Nanoparticles zeta potential ?

Is there any mathematical relationship between zeta potential and both the polydispersive index (PDI) and pH of the zero-point charge of the nanoparticles?

28 April 2024 8,728 5 View

Fast Question: Do hydrochloride salts run on a TLC plate?

Basically, I have deprotected a BOC, TPDMS-Protected sphingolipids using Acetyl Chloride, which gave a salt of deprotected sphingolipids. Can salts run on TLC?!

25 April 2024 2,971 1 View

How can we create these plots?

how can we create these plots? a 3-dimensional look and showing strength with colour, which software does create these pictures? source of image: Directive giant upconversion by supercritical...

02 April 2024 9,999 4 View

Is it possible to grow graphene on the vertical wall of a structure, for example on the vertical walls of a SOI waveguide?

09 March 2024 1,990 2 View

What is the impact of shopping mall architecture designed on consumer's behavior?

does architectural designe influence the consumers attitudes and their intention to shop and buy.

05 March 2024 7,975 5 View

How can I convert files formate from (.spu)into (.CNF) ?

There are many applications that used for gamma spectral detection and analysis but some of them are more suitable for me in detection usage and others in analysis usage and these applications...

01 March 2024 5,459 0 View

Does anyone know, any conference related to "mathematical data compression" topic?

Please suggest me, I want to present my research work.

13 July 2024 1,461 1 View

Difference between creep deformation and stress relaxation deformation ?

I understand the basic definitions of creep and pressure relaxation. However, I am confused about the exact difference between them. See attached photo. Because a compression force is applied,...

17 June 2024 5,344 2 View

What is the recommended safe distance between drilled holes in fiberglass, and which standard governs the drilling process?

Material : Fiberglass sheet thickness : 3mm

03 June 2024 6,255 0 View

How can the Poisson's ratio be calculated from stress-strain curves (with images taken at 100 fps)?

I have conducted uniaxial compression tests on my 3D printed samples. Since these are perforated samples, ideally they should have negative (or near zero) Poisson's ratio. However, DIC (digital...

21 May 2024 9,967 0 View

What are the ways to reduce the hydrophilicity of synthetic fibers without affecting their mechanical properties?

For example. Kevlar 49 or e-glass fibers.

18 May 2024 6,109 2 View

Wannier90 error: Could not find projections block in wannier90.nnkp?

Hello ~ I'm currently beginner using Wannier90. My target molecule is "EuTiO3". The electron configuration of this molecule is as follows: Eu: 1s2 2s2 2p6 3s2 3p6 3d10 4s2 4p6 4d10 5s2 5p6...

06 May 2024 2,066 1 View

Abnormal distortion on shell element (S4R) under Abaqus explicit compression?

Hi everyone, I have a question that has been bothering me for a month. In Abaqus Explicit, I used shell (S4R) to simulate a compression experiment. I chose 'general contact' with 'all* with...

22 April 2024 3,975 4 View

What should be the End Time, velocity and other settings in ANSYS Workbench Explicit Dynamics to simulate Quasi-static compression?

I am trying to model a quasi-static compression of a complex structurAl geometry. The experiment was done at 2 mm/min of loading. I am using ANSYS Explicit Dynamics. I’m also using Automatic Mass...

20 April 2024 2,934 4 View

How to check tensile and compressive stress values generated after analysis of model in abaqus/CAE ?

I am comparing a simple tensile stress and compressive stress results getting from Abaqus with my manual calculations. But, I could not able to find out where to check the value of tensile and...

19 April 2024 5,186 2 View

Why we have bubbles defects on the surface defects on a rubber material ?

As you can see below an SEM image of a rubber (this rubber formulated with EPDM + blowing agent'OBSH' + oil + other chemicals agent), I recently noticed that the material contains a lot of bubbles...

16 April 2024 8,395 0 View