Why is the cross model in ANSYS Fluent different to other formulations of the cross model?

05 July 2021 0 2K Report

Why is the cross model equation that fluent uses different to other formulations? Here are the formulas and I am quite unsure as to why fluent has its own slightly different version.

Badges
Science topic

More Alireza Meghdadi's questions See All

What do you know about classroom management?

Hello, if possible, please send me new methods of management and communication in the classroom. thank you؟

18 June 2024 4,139 3 View

How do we measure the electrical conductivity of this magnetic nanocomposite?

A magnetic nanocomposite has been synthesized and its electrical conductivity needs to be measured. What analysis and technique can be used to measure the electrical conductivity of this magnetic...

16 June 2024 7,488 3 View

Is it possible to estimate Horizontal in-situ stresses' directions and magnitudes from seismic data by using AI methods?

We know that one of the important members of a 3D Geomechanical Model is in-situ stresses' directions and magnitudes. we can use the seismic data to estimate these parameters in special record...

21 May 2024 1,332 2 View

Hello. why do we measure surface tension?

surface tension

20 May 2024 4,895 1 View

What are the S-scheme and Z-scheme heterojunctions in photocatalytic systems? for the types of heterogeneous photocatalysts, how can you determine?

what are the S-scheme and Z-scheme heterojunctions in photocatalytic systems? and for the types of heterogeneous photocatalysts, how can you determine the type of S-scheme and Z-scheme?

16 May 2024 1,545 1 View

Why is my first article being rejected fast by related journals?

Hello everyone, I hope you are all doing well. I have already checked plagiarism, related articles’ structures, and grammar, and they seem fine, but good impact factor journals that I have written...

15 May 2024 1,007 4 View

Altitude control of a quadrotor ?

hi there i'm working on quadrotor path tracking in matlab's simulink . there is an inner loop which is responsible for tracking the desired euler angles generated by the outer loop . feedback...

05 May 2024 7,705 5 View

How to perform LC-BLYP calculation with GAMESS?

Hello Dears, I am currently working on time-dependent density functional theory (TDDFT) calculations for both singlet and triplet states using the LC-BLYP functional in GAMESS. I believe I have...

01 May 2024 4,614 0 View

Does Baicalein interact with DMEM high glucose or FBS?

greetings, I'm culturing SW480 cells on DMEM high glucose gibco with FBS. When I'm performing MTT Assay, upon treatment of cells with Baicalein, the color of medium with 5% FBS changes to dark...

25 April 2024 7,115 4 View

I'm getting error:( Domain error. To compute complex results from real x, use 'sqrt(complex(x)) ) in simulink?

hi there . i'm currently working on a thesis which involves designing a fast nonsingular terminal sliding-mode controller for attitude control of a quadrotor. the outputs of sliding mode...

20 April 2024 425 2 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View

Why i can't get access to isosurface in fluent?

hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.

03 July 2024 5,418 4 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to converge PEMFC in Ansys Fluent?

I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...

26 June 2024 2,358 0 View

What is the exact mathematical formulae and the C++ code of EMMS drag model that is used and applied in ANSYS Fluent 2023?

EMMS - Energy Minimization Multi-Scale

18 June 2024 5,857 2 View

How to compile a udf in Fluent to import hourly weather data and update the boundary condition based on it ?

Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...

14 June 2024 6,480 0 View

Fluid flow through copper tube?

What does it mean meshed wall and shell conduction with or without run-out method use to meshing copper tube in Ansys fluent?

07 June 2024 9,030 3 View

How to address gradient discontinuities in CFD - Ansys Fluent?

Assuming I have three domains (three cubes e.g.) placed side by side, the electrical potential equation ( which I am specifying as a User Defined Scalar (UDS)) is solved in the left and right...

05 June 2024 4,153 0 View