Could you get me this report, please?

03 April 2018 7,186 1 View

Hi Please as you know that neutrophils are the only cells that can express Ly6G. So can I ask which antibody is specific for this marker?

actually, some references mentioned to use Gr-1, however, I think it would be inappropriate to use Gr-1 antibody as it was reported before that it contains antibody for both Ly6C and Ly6G whereas...

02 March 2018 8,397 1 View

The most common types of bacterial contamination that affecting the growth of anadara granosa or Blood Cockles?

Dear all Professors, Researchers, and Colleagues, I need your help by list ''What are the frequent types of bacterial contamination that affecting the growth of anadara granosa or Blood Cockles...

10 November 2017 1,943 0 View

Why assigning the shell section by selecting middle surface, top surface, or bottom surface to represent the reference surface makes difference?

I'm modeling thin-walled columns using shell element in ABAQUS. I'm using different ways to shape the geometry to end up with the same final configuration whatever the way is. I noticed that when...

09 October 2017 1,061 0 View

Do I need to do Symmetry for beam element?

Dear all, I'm trying to reduce the computational time for a model which contains circular shell element and beam element (with pipe profile) in the top ( see the attached pics). Do I need to do...

05 June 2017 8,630 3 View

What are the parameters should I input for this UMAT code to get results similar to ABAQUS GUI?

I just wrote the Isotropic Hardening rule Fortran code (attached below), which is similar to what's available in ABAQUS library, if you have experienced with this code before, what are the...

31 December 2016 5,980 3 View

What's the procedure to get the original written data from a figure in published paper?

I'm wondering if there is a way to get the original data for some figures in published research papers? I've tried to contact the authors, but no responses come back, could I get this data from...

11 December 2016 9,775 2 View

Thin-walled column under constant axial and lateral cyclic loading?

26 October 2016 3,362 6 View

How can I export or import part, sketches or assemblies from ABAQUS?

I want to use the same geometry that I drew it in ABAQUS and import again in a different ABAQUS model (not copying). I'm trying with File-export to save it, but when I'm gonna import it again, it...

09 October 2016 6,450 4 View

Link ABAQUS 6.14 with intel parallel studio XE 2016?

09 October 2016 2,061 5 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials?

Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...

25 February 2021 9,936 2 View

Is it possible to do optimization for a submodel in Abaqus?

I'm trying to run an optimization in Abaqus for a submodel with no luck, jobs are not being create for submission. Is this even possible? or is Abaqus limited to do Opt. for the model itself...

24 February 2021 4,908 5 View