Could you get me this report, please?

Qusay A. Al-Kaseasbeh @Qusay_Al-Kaseasbeh

04 April 2018 1 7K Report

Public work research institute of Japan. 1997–2000. Report of cooperative research on limit state seismic design for bridge piers, I-VIII and summary.

Bassam Tayeh

Following the answers

Badges
Science topic

More Qusay A. Al-Kaseasbeh's questions See All

Hi Please as you know that neutrophils are the only cells that can express Ly6G. So can I ask which antibody is specific for this marker?

actually, some references mentioned to use Gr-1, however, I think it would be inappropriate to use Gr-1 antibody as it was reported before that it contains antibody for both Ly6C and Ly6G whereas...

02 March 2018 8,474 1 View

The most common types of bacterial contamination that affecting the growth of anadara granosa or Blood Cockles?

Dear all Professors, Researchers, and Colleagues, I need your help by list ''What are the frequent types of bacterial contamination that affecting the growth of anadara granosa or Blood Cockles...

10 November 2017 2,040 0 View

Why assigning the shell section by selecting middle surface, top surface, or bottom surface to represent the reference surface makes difference?

I'm modeling thin-walled columns using shell element in ABAQUS. I'm using different ways to shape the geometry to end up with the same final configuration whatever the way is. I noticed that when...

09 October 2017 1,146 0 View

Do I need to do Symmetry for beam element?

Dear all, I'm trying to reduce the computational time for a model which contains circular shell element and beam element (with pipe profile) in the top ( see the attached pics). Do I need to do...

05 June 2017 8,704 3 View

How to create hard contact between concrete and steel?

I'm modeling Concrete filled steel tube column, but contact properties do not work for me. please check the input file to get more information.

12 March 2017 9,989 11 View

What are the parameters should I input for this UMAT code to get results similar to ABAQUS GUI?

I just wrote the Isotropic Hardening rule Fortran code (attached below), which is similar to what's available in ABAQUS library, if you have experienced with this code before, what are the...

31 December 2016 6,059 3 View

What's the procedure to get the original written data from a figure in published paper?

I'm wondering if there is a way to get the original data for some figures in published research papers? I've tried to contact the authors, but no responses come back, could I get this data from...

11 December 2016 9,837 2 View

Thin-walled column under constant axial and lateral cyclic loading?

Hi, I'm modeling thin-walled column under axial loading and horizontal displacement as shown in attachment 1 using displacement control (Boundary conditions). I decide and input the horizontal...

26 October 2016 3,462 6 View

How can I export or import part, sketches or assemblies from ABAQUS?

I want to use the same geometry that I drew it in ABAQUS and import again in a different ABAQUS model (not copying). I'm trying with File-export to save it, but when I'm gonna import it again, it...

09 October 2016 6,592 4 View

Link ABAQUS 6.14 with intel parallel studio XE 2016?

Hi all, I'm trying to Link ABAQUS 6.14 with intel parallel studio XE 2016, and Microsoft visual studio 2013 professional, could you please tell how I can do that? or what kind of Intel parallel...

09 October 2016 2,143 5 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

Is Galaxy.org good to use for research for analyzing data and for publication?

Hello all, I wanted to know, can I use galaxy (USA, Europe or Australia) platform for analyzing the shotgun data, and can it be used for publication purpose as well? Thanks :)

06 August 2024 6,610 4 View

Research Methodology - Impact of Corporate Reputation on Stakeholders Behaviors?

Please can anyone support with the survey questions based on RQ measures and propose how to do it in FMCG industry and include as well the role of brand equity Thanks

06 August 2024 949 0 View

How to convert a privately loaded document into a public document?

I attempted to make a privately uploaded text public but a window appeared that said an error occurred. There was no explanation provided as to why there was an error or what might be done to...

05 August 2024 8,025 7 View

Anyone having idea about VN primer for miRNA primer design ?

How to design VN primer to attach with universal reverse primer

05 August 2024 2,116 3 View

Should I remove an item from a scale to raise Cronbach's alpha and McDonald's omega or is it better to leave it if they are both over .7 already?

Hello! I have this scale which had 10 items initially. I had to remove items 8 and 10 because they correlated negatively with the scale, and then I removed item 9 because Cronbach's alpha and...

01 August 2024 4,606 7 View

How to send my account link and how to make my account public?

Nothing

01 August 2024 755 1 View

How can productivity (using the Google form link below to provide your answers) be achieved in manuscript publication?

Survey on Productivity in Journal Manuscript Publication Survey Form Link: (https://forms.gle/YRVrn8dL4WZJJ79S8 ) Dear Researcher, We kindly invite you to participate in our survey focused on...

29 July 2024 4,116 1 View

How to Input and Analyze Results for an Asymmetrical Factorial Design in STATISTICA 13.3?

In STATISTICA 13.3, I used the Experimental Design Builder under the Design of Experiments tab to generate a design matrix for an asymmetrical factorial design (1443) with 12 experiments. However,...

29 July 2024 4,155 2 View