Where can I get a functioning SEM Machine?

More Olanrewaju Apampa's questions See All

Is it possible to filter Virus out of air, what filtration method (s) will you recommend and what efficiency will you predict?

is it possible to filter Virus out of air, what filtration method (s) will you recommend and what efficiency will you predict?

07 April 2020 3,152 0 View

Waste heat reuse temperature?

In experimenting reuse of waste heat/exhaust fumes, can I use waste heat from electric generating set for heating in refrigerating cycle, Is it practicable? Rankine and Vapour Absorption cycles...

05 February 2020 2,290 4 View

Nanoparticles in lubricants ?

How is it that we propose nano particles in lubricants, for instance, engine oil. To what extent does the particle size in relation to viscosity affect the metal surfaces. Is it a trade off due...

03 February 2020 7,626 4 View

Which one is better to use for water stress experiment GWAS or RNASeq?

Hi everyone, This is my first time in this area of research. I am working on 95 varieties of bambara groundnut. I have done the agromorphological characterization of these varieties as well as the...

09 September 2019 3,920 4 View

What salt could be used to replace cyanide salt for carbo-nitriding in salt bath heat treatment?

I desire a locally available salt that is not poisonous as cyanide salt to be use in salt bath furnace operations.

17 June 2019 2,993 0 View

Problematic blunt end restriction enzyme digestion?

i have tried so many times to perform a partial digest with MsAp1I restriction enzyme (creates blunt end) on F88-4 phage vector(9234bp), it has 2 sites which overlaps a CpG site, which i read...

05 March 2019 6,623 2 View

How can i set up a meaningful drought experiment?

Hello, I want to set up a drought-response experiment. Should i consider using the green house or the field. Secondly, will 100 accessions of this crop be too much for the experiment? Lastly, will...

06 August 2018 1,648 6 View

Kindly explain by calculation how one can determine the % weight loss of molecules from the TGA curves? State with illustration in a stepwise order.?

Consider TGA curve of a mixed-ligand metal(II)complex of like 3 or 4 steps decomposition pattern?

01 June 2018 144 8 View

How can I protect a picoammeter or a picoscope in HVDC measurements?

I'm trying to measure the leakage current along an insulator energize with HVDC (the effect of space charges is been considered). - Can I connect a picoammeter to the ground electrode? If...

26 June 2017 8,616 7 View

Hello everyone, please what is the best protocol for extracting secondary metabolites from rhizosphere bacteria?

I am working on rhizosphere bacteria and need to identify the secondary metabolites they produce which aid in their biocontrol ability. Thanks

30 August 2016 9,044 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

1. If I can quantize the atom using this hyperbolic spiral and classical physics, could nature do the same?

If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...

07 August 2024 5,343 2 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Weak DAPI staining after immunohistochemistry - how to improve?

After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...

05 August 2024 9,637 2 View

Hugh J Byrne

SEM provides a surface morphology, but not a chemical analysis, unless you add EDAX/WDAX

Janusz Rebis

SEM with EDS may help, maybe XRD?

Qais Almaamari

following

Mayowa Bakare

SEM machines are available in many universities. It may help if you define to what extent you want to travel to get this done. Thanks

Abolore Adebayo Musari

SEM machine is available at Kwara state university also at SHESTCO (Sheda Science and Technology complex) Abuja beside National Mathematical centre.

You can also discuss with Dr. Abatan for details