Despite single-cell RNA, how can I characterize a new cell subtype/phenotype?

A new cell subtype was found out only during regeneration phases after a cuprizone-induced demyelination model. How can I characterize this cell? It is important to highlight that was already...

13 February 2021 1,245 1 View

Permanent Fluid temperature initialization in Ansys Fluent?

Dear researchers, I am coupling Design Optimization with ANSYS Fluent in Workbench 2020 R2. I can do the analysis. I am patching the initial Temperature values of the zones. However, the patch...

28 January 2021 4,265 2 View

Luciferase assay for miRNA-gene: How to obtain DNA (PCR product) from the mutated primer?

To perform the Luciferase assay for microRNA-gene interaction its necessary a primer (wild-type) to amplificate the specific ligation site and also a mutated primer. But if your primer has a...

19 January 2021 8,568 3 View

How to couple Moldex 3D with MATLAB for design optimization of an injection mould?

Hello, I would like to use the software Moldex 3D for the design optimization of an injection mould. How can I couple Moldex 3D with a MATLAB code? Any help appreciated, I wish you all a happy...

09 January 2021 569 2 View

How to setup ANSYS Fluent for simulating the filling stage of an injection mould?

Hello, I am using ANSYS Fluent for simulating the filling stage of an injection mould. However, when comparing the results with those of specialized software, such as Moldex 3D, I found the...

07 January 2021 7,992 1 View

Which plants and trees have the best ability to prevent the entry of particulate matter (PM2.5 and PM1) and nanoparticles in indoor environments ?

In recent years our group has highlighted the importance of trees and plants in public and recreation parks in large mega cities. However, we are interested in developing "green shields" to be...

05 January 2021 6,500 3 View

How to phosphorylate specific residues on pymol?

Hi everyone, I am using the pyTMs plug in on Pymol to phosphorylate a particular threonine in my protein. I am having difficulty in selecting only one or two residues - it seems I can only...

05 January 2021 230 3 View

How to perform Potential Surface Energy Exploration (PES) calculations?

I would like to receive help, as I am trying to make an analysis of the ethanol PES, but the calculations are always giving error. I use the conda-forge version of xtb (* xtb version 6.3.2...

04 January 2021 602 2 View

How do you create a funnel plot in STATA to assess publication bias using proportions from the metaprop command (for a meta-analysis)??

Hi everyone! I am trying to use STATA to create a funnel plot to asses publication bias using proportions from studies for a large meta-analysis (having used the metaprop command). I"m having...

09 December 2020 6,096 3 View

How to get the model shape matrix from Nastran?

I need to include the bending mode dynamics in my simulation. So far, I am only considering the rigid body dynamics. So I need to implement the following equation: q'' + Kg*q = Phi*F(t), where:...

19 November 2020 4,270 5 View

How to check the uv-vis absorption of nanoparticle by surface plasmon resonance?

I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?

01 March 2021 930 3 View

How to remove fatty material from plant extract?

The resultant solid was partitioned three times with 250 ml of petroleum ether (40-60/c) to remove any fatty material and evaporated to dryness.

28 February 2021 9,464 2 View

Is there a method of determining feed digestibility without the need to re-pellet the feed?

I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....

28 February 2021 7,967 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Unknown debris sheets observed in cell culture flasks?

Hi, We culture neural progenitor cells in T175 culture flasks coated with PLO-Laminin. We have successfully grown these cells with our protocol for months. Recently, we observed large sheets...

25 February 2021 3,443 4 View

How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

Is there a suitable way to confine cell attachment area inside a multi-well plate?

Are there any types of cylindrical cell culture inserts that are designed to confine cell seeding area? Say, if I'm using a 12 well plate (3.5 cm^2/well), but only want to seed cells in the middle...

22 February 2021 7,127 4 View

How to improve the adhesion between germanium and silicon monoxide thin film layers using EBEAM evaporation?

I want to deposit multilayer coating of germanium and silicon monoxide on silicon wafer using ebeam evaporation?

21 February 2021 2,141 3 View