Reference about advanced Li-Ion batteries production technologies (and methods)... ?

Dear researchers, I'm studying about manufacturing of Advanced Li-Ion batteries . I'd like have some information about technologies and methods for the production of the battery and its...

30 October 2020 1,009 2 View

Fuel Cell modeling in Aspen Plus and Aspen Custom Modeler?

Hello, I modeled a case in Aspen Custom Modeler at two modes (isotherm and non-isotherm) successfully. I exported them to Aspen Plus, but the non-isotherm case diverges and mass balance error...

22 December 2019 2,460 4 View

Which kind of Battery Model is very usefull in Simulink a Battery equalizer Circuits?

I Want to Simulink some topologies of Battery Equalizer Circuits in Orcad Capture & MATLAB simulink so I need to use a good Circuit model for Lithium Ion Batteries. I have different data...

08 November 2018 1,270 3 View

Simulation of circulating fluidized bed with comsol 5.3?

I tried to simulate a circulating fluidized bed using comsol multiphysics 5.3 based on attached PDF, but i received this error : Nonlinear solver did not converge. Maximum number of segregated...

19 October 2018 2,190 3 View

I'm going to link the aptamer and the quantum dot graphene by linking the Pi-Pi stacking?

I'm going to link the aptamer and the quantum dot graphene by linking the Pi-Pi stacking. But I do not know how much of a volume fraction, at what temperature, how long will I be in the Shaker....

09 November 2017 3,592 1 View

Which countries in ASIA implemented water intensive commodities import policy in their trade strategies (virtual water policy) ?

08 September 2016 4,636 4 View

How can I define RHS in UEL for a static analysis?

Hi every one! I'm working on developing a shell element to be implemented in ABAQUS through UEL. It's going through a static analysis. and as you may know for static analysis, ABAQUS just needs...

02 September 2015 7,641 9 View

How can I print out the global stiffness matrix in ABAQUS?

Hi everyone, I'm using UEL in ABAQUS. My model just have one 4-node beam element (defined in UEL) fixed in one end.When I'm running the UEL, it's working without any problem. But when I'm trying...

25 February 2015 8,975 3 View

Distribution of nanoparticles inside a binary polymer blend?

05 January 2015 6,019 6 View

How can I find the names of genes by accession number and sequence ID obtained through ncbi?

I want to report the name of the gene for loci that have been obtained through blast ncbi.

25 May 2014 8,049 8 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

How to improve the adhesion between germanium and silicon monoxide thin film layers using EBEAM evaporation?

I want to deposit multilayer coating of germanium and silicon monoxide on silicon wafer using ebeam evaporation?

21 February 2021 2,141 3 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

How do I calculate absorption coefficient of my thin film if I dont know the thickness? Or how can I calculate the thickness of my sample?

I have done Uv-vis characterisation of my thin film and have received absorbance and transmittance data. Now I want to calculate the absorption coefficient but I dont know the thickness of my...

21 February 2021 7,148 8 View

How to construct different filler shape in MD simulations?

Is there any way to construct different initial filler shapes like triangle, square, rectangle, pillar, and tube in any simulation software.

20 February 2021 1,750 1 View

Can fractal dimension of thin film surfaces affects the electrons energy states?

As fractal dimension of a thin film surface implies the irregularity in the surface. Is it possible that the energy states of the electrons are also affected by the fractal dimension?

19 February 2021 5,509 3 View

What is the reason film thickness increased?

what is the reason film thickness increased when increased doping concentrations give some reasons The measured film thickness is 156, 282, 394, 548 and 681 nm for 0, 1.5, 2.5, 3.5, and 4.5 wt....

17 February 2021 8,987 5 View