Has anyone used an inertial navigation system with RTK (Real Time Kinematic)?

INS-RTK modules claim to be close to a cm accuracy, has anyone used one and if so, how expensive can the telematic charges be if I have a case to run it 18h per day?

14 December 2020 6,139 8 View

What are first, second and third cracks (red, green&blue color outline) in crack pattern of RC beams in ANSYS APDL?

Hello everyone, Can anyone kindly explain what is mean by three different colours of cracks in RC beams in ANSYS APDL and the features of first crack (red colour outline) second crack (green...

17 November 2020 2,512 1 View

Having an issue with defining sub caption in the Springer LaTeX file ?

Dear All, I am facing defining the sub caption issue in the Springer LaTeX file. If I define the sub caption in the Tex file, it exhibits an error while compiling. In general, Springer, LaTeX...

17 October 2020 6,473 2 View

What should be reason for higher values of Ultimate results for RC beam simulations in ANSYS APDL?

My RC beams experimental ultimate load & deflection was 97kN and 20mm resp. But when I model it in ansys apdl it run continuously up to a load of 140kN and 60mm deflection and still...

02 October 2020 8,747 2 View

Why the solution runs continuously even after reaching ultimate strength of beam in ANSYS APDL?

I am analyzing RC beam in APDL and tried convergence criteria with F=0.05 once then U=0.05 and also tried both criterias simultaneously but what I found is my solution continuous even upto twice...

02 October 2020 1,490 2 View

Need "E.Hognestad;" compressive stress-strain curve explanation?

Can anyone kindly explain in case of Hognestad compressive stress-strain curve for concrete, they have given fc" =0.85fc', but why researchers are use fc"=fc' instead. Where fc" =ultimate...

14 August 2020 7,508 3 View

How to perform Molecular dynamics (MD) simulation for corrosion system ?

Dear researchers, Greetings! Please help me to study surface of Fe(110) with Organic Corrosion inhibitor molecules using Materials Studio software. Kindly give suggestion to create a simulation...

02 August 2020 4,267 2 View

What characterization method is used for realizing different phases in a micron size particle?

12 March 2020 6,331 14 View

Which Fuzzification Technique for Ordinal Dataset ?

I have an ordinal dataset on the scale of 1 to 5 based on household surveys about the intensity of agreement (5 being strongly agreed to 1 being strongly disagreed) of residents about certain...

11 March 2020 6,308 2 View

No title

28 August 2019 2,091 6 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View