12 December 2016 1 7K Report

you may have a case already modelled ....

More Ibrahim O. Elhagali's questions See All
Can saline water be used to cool the photo voltaic modules?

You know that cooling of the PV modules helps increase the efficiency, but can we use saline (salty) water in this process without having any harmful effects to the modules? note that the saline...

03 April 2019 7,519 11 View

I am using Spalart_Allmaras model to capture the wingtip vortex, so i can choose the Y+ whether to be 1 or higher than 30... read the explanation?

I have chosen the 1st layer thickness value so that the walls of the wing has Y+=1 and the other walls in the fluid domain Y+=30. the question is will Fluent distinguish the two cases and...

31 December 2018 6,745 0 View

You know the journal file in Linux which is read through the terminal, do you know any similar file type that can be read through the cmd in Windows?

I want to run a program in an automatic way using windows command window, so I want to make something like journal file in Linux.

31 December 2018 9,974 0 View

I want to access a workstation to make ANSYS simulations, can you help?

access to a workstation

11 December 2018 6,716 3 View

I want to validate the simulation of flow around NACA 0012 using drag and lift coef how to extract raw Data from the paper?

NACA0012

11 December 2018 9,322 4 View

Which programs can be used to collect all these velocity profiles in the same figure?

I want to add velocity profiles as shown in the figure, at each location in in x direction i want to plot the velocity profile (velocity VS y coordinate)

09 October 2018 3,120 9 View

What does " unassigned interface zones found " in FLUENT mean ?

....

11 December 2016 8,373 0 View

What is the material that has the lowest ionization temperature ?

i want to know a gas that has a low ionization temperature

11 December 2016 5,743 2 View

ANSYS FLUENT, in convection problems why i have to use "Fill" tool, and why i have to make all the parts as one part?

.......

11 December 2016 10,000 0 View

Why in heat transfer by conduction the penetration distance does not depend on temperature ( the driving potential ) ?

>>>>

10 November 2016 4,447 9 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close