I want to access a workstation to make ANSYS simulations, can you help?

More Ibrahim O. Elhagali's questions See All

Can saline water be used to cool the photo voltaic modules?

You know that cooling of the PV modules helps increase the efficiency, but can we use saline (salty) water in this process without having any harmful effects to the modules? note that the saline...

03 April 2019 7,584 11 View

I am using Spalart_Allmaras model to capture the wingtip vortex, so i can choose the Y+ whether to be 1 or higher than 30... read the explanation?

I have chosen the 1st layer thickness value so that the walls of the wing has Y+=1 and the other walls in the fluid domain Y+=30. the question is will Fluent distinguish the two cases and...

31 December 2018 6,814 0 View

You know the journal file in Linux which is read through the terminal, do you know any similar file type that can be read through the cmd in Windows?

I want to run a program in an automatic way using windows command window, so I want to make something like journal file in Linux.

31 December 2018 10,047 0 View

I want to validate the simulation of flow around NACA 0012 using drag and lift coef how to extract raw Data from the paper?

NACA0012

11 December 2018 9,395 4 View

Which programs can be used to collect all these velocity profiles in the same figure?

I want to add velocity profiles as shown in the figure, at each location in in x direction i want to plot the velocity profile (velocity VS y coordinate)

09 October 2018 3,210 9 View

What does " unassigned interface zones found " in FLUENT mean ?

....

11 December 2016 8,518 0 View

I want to model boundary layer (separation) control using ANSY Fluent so if you can help ?

you may have a case already modelled ....

11 December 2016 6,752 1 View

What is the material that has the lowest ionization temperature ?

i want to know a gas that has a low ionization temperature

11 December 2016 5,850 2 View

ANSYS FLUENT, in convection problems why i have to use "Fill" tool, and why i have to make all the parts as one part?

.......

11 December 2016 10,060 0 View

Why in heat transfer by conduction the penetration distance does not depend on temperature ( the driving potential ) ?

>>>>

10 November 2016 4,515 9 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Which Scopus Journal provides the most affordable fees?

"PUBLISHING IN A SCOPUS JOURNAL" Researchers are now at a cross road. The critical need to publish in a Scopus or ISI, etc journal is ever vital. Journal Publication fees must be submitted....

10 August 2024 8,621 1 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Seeking Advice on Viability and Execution of Undergraduate Thesis Topic?

Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...

10 August 2024 8,992 0 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Request Python code?

Request Python code from this article : Gender equity of authorship in pulmonary medicine over the past decade. THANKS!

08 August 2024 6,242 2 View

Who will be moral responsible for the death of thousands of people in the event of an earthquake?

Who will bear moral responsibility for the deaths of thousands of people in the event of an earthquake? Weeks and months remain before the onset of strong earthquakes that bring death to...

08 August 2024 6,134 12 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Thomas Frank

Not sure what you are asking for? With the ANSYS Students edition essentially everyone can install a node-/cell count-limited version of ANSYS on its own laptop / computer and do some ANSYS simulations.

Hamit Solmaz

I dont believe anyone can share workstation of external bpn connection. You should find an other way. Dont waste your time.

Sarthak Nag

Try using ANSYS with Amazon Web Services (AWS).

https://aws.amazon.com/partners/success/ansys/

Hope it helps!