How we can import scalar parameter from txt file in ANSYS?

12 December 2013 1 432 Report

I use *vread command to import array parameter to ANSYS, but I do not know how to import scalar parameter?

You must use the *vread command to specify an vector or matrix, and using the command *set you allocate the vector element to scalar parameter.

Badges
Science topic

More Vahid Dabbagh's questions See All

How to analysis gears contact in Asnsys static structural with frictionless contact type?

I model and simulate the contact between two gear. I applied torque on one of the gears and I fix the other using fix displacement in Ansys. Automatic contact detects the contact between gears...

11 December 2019 7,367 3 View

Why nobody in the world thinking about how to make houses less expensive?

There are plenty of space available for making the procedure of building of a house less expensive, however, nobody in the world thinking about it and it is so weird. We know that the labor cost...

03 April 2019 3,861 3 View

Can I model hyperelastic material in Abaqus Explicit?

I want to model a simple hyperelastic material to be moved when I apply a pressure on its face. But, the model does not move at all. It seems that the force does not influence other elements that...

07 August 2018 6,871 2 View

Is it possible to upgrade python version of Abaqus?

Even the latest version of Abaqus ran with python 2.7 and it comes with numpy version 1.6. To be able to use latest version of scipy, I need to upgrade numpy. In addition, the package does not...

06 July 2018 3,615 1 View

Is piezo layers in a Piezostack is compressed when they are manufactured?

I am trying to model a piezostack in Abaqus. But the result of force generation I obtained is almost two times the amount mentioned in catalogue. In the analysis I did not specify any initial...

02 March 2018 7,050 1 View

How to apply Pasternak foundation in Abaqus?

I know that in Abaqus there is a way to apply foundation which is through interaction modulus. However, using this method only Winkler type foundation can be defined. While, I need to define...

01 February 2018 9,610 3 View

How to write heat transfer abaqus subroutine to get steady state soultion?

I know that by using the UMATHT subroutine, one can write a heat transfer equation subroutine, but it is for transient analysis. Can I use same subroutine to get steady state solution or I must...

11 December 2017 6,601 3 View

I want to model a fluid problem using abaqus/cfd, but I can not find steady state solution?

I want to model a fluid problem and solve it using steady state solver. I tried to find an option for that. Default is transient analysis. I do not know how to change it to steady state form.

11 December 2017 5,536 3 View

What is the boundary condition between piston and cylinder in a hydraulic jack?

I intended to model a structure with a hydraulic to move it up and in addition I want to use that model to do a vibration analysis using either Ansys or Abaqus. However, I wonder, How I must model...

11 December 2017 1,078 2 View

Are two identical clocks located in two far places in the universe measure same value?

Assume we have two identical clocks made on the earth. One of them is sent to other corner of universe (I mean very far). The clock starts to tick simultaneously (Maybe it is not practical in...

06 July 2017 2,851 12 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View