How to simulate Boundary layer on a rotating circular cylinder ?

I am solving axisymmetric boundary layer developed on a rotating circular cylinder using Fluent code. In a model, I modeled only fluid domain which have inlet, outlet, no-slip and free-stream...

11 December 2019 4,659 5 View

Hartree parameter \beta_{H} for wedge flow ?

I am simulating flow over an inclined flat plate using fluent. I want to compare this velocity profile with the Falkner-Skan profile. 1. what will be the value of Hartree paramer ( beta ) and...

06 July 2018 6,867 0 View

How solve incompressible flow over an inclined flat-plate using fluent ?

I am simulating flow of water on a inclined flat-plate at 8-10 degree with the x-axis. The rectangular domain is generated and discretized. The inlet and outlet boundaries are normal to the...

05 June 2018 6,594 1 View

How one can make expansion of temporal eigenmodes computed by the solution of Eigenvalues problem ?

07 August 2017 8,595 1 View

OUT FLOE BOUNDARY CONDITIONS

04 May 2016 8,630 0 View

How we can transfer velocity field and its derivatives from cylindrical coordinates to spherical coordinates ?

03 April 2015 7,959 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View