How to simulate Boundary layer on a rotating circular cylinder ?

I am solving axisymmetric boundary layer developed on a rotating circular cylinder using Fluent code. In a model, I modeled only fluid domain which have inlet, outlet, no-slip and free-stream...

11 December 2019 4,659 5 View

How solve incompressible flow over an inclined flat-plate using fluent ?

I am simulating flow of water on a inclined flat-plate at 8-10 degree with the x-axis. The rectangular domain is generated and discretized. The inlet and outlet boundaries are normal to the...

05 June 2018 6,594 1 View

How to simulate axisymmetric boundary layer on a rotating circular cylinder using fluent ?

I want to simulate an incompressible axisymmetric boundary layer on a circular cylinder with rotating cylinder in Fluent. Thanks

10 November 2017 8,180 2 View

How one can make expansion of temporal eigenmodes computed by the solution of Eigenvalues problem ?

07 August 2017 8,595 1 View

OUT FLOE BOUNDARY CONDITIONS

04 May 2016 8,630 0 View

How we can transfer velocity field and its derivatives from cylindrical coordinates to spherical coordinates ?

03 April 2015 7,959 4 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Is there any test to determine the cardiovascular risk of patients with obesity? from the perspective of obesity?

We found tests to determine cardiovascular risk taking into account lipid profile, blood pressure, age, history of diabetes, other laboratories. But when weight is involved, there is a paradox. I...

02 March 2021 6,036 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View