How to set OUTFLOW boundary condition in ANSYS FLUENT using TUI?

More Ijaz Fazil Syed Ahmed Kabir's questions See All

Can the set up files created for openfoam v4.0 (from .org) can be used for openfoam 1906 (from .com)?

I noticed that openfoam software is provided by two different organisations 1. ESI group 2. OpenFOAM foundation. My doubt is if the cases are set based on the version provided by openfoam...

31 December 2019 4,885 2 View

Is meshgems (add on module in salome) is good for hexmeshing of fluid domain to be run in openfoam?

Hi I'm currently using snappyhex mesh for meshing my fluid domain to run simulation in openfoam. I found salome is better free alternative to snappyhexmesh, but the time required by the mesh...

10 November 2019 1,740 1 View

Why the flow direction seems fixed along 'x' axis in OpenFOAM 6 (I apologise I found no issues with velocity compoent)?

I recently updated my OpenFOAM version 4.0 to 6. I'm facing an issue in the direction of flow. My flow is always pointing in x direction. Hence I tried to change the flow axis in a tutorial...

08 September 2019 5,794 1 View

Is just the pressure raise on closing the valve causes water hammering?

I recently saw this lecture from NPTEL on water hammering. I suppose example used for explaining the wave motion is widely used. (flow from a reservoir and valve...

07 August 2019 1,927 4 View

How to determine the suction pressure of multiple pumps operating in parallel?

Hi Im doing an analysis on total head developed by a pumping station that has 6 pumps. We have measurement reading for pressure on delivery side, but unfortunately volume flow rate is measured at...

09 October 2018 4,357 1 View

How to determine the head rise in vertical turbine pump?

Dear all, I'm looking to apply Bernoulli's principle to determine the head rise in the pump. Since most of the lectures are based on centrifugal pump, there is a suction pipe and delivery pipe,...

09 October 2018 10,195 0 View

What is the difference between freestream BC and inletoutlet BC?

I'm confused how freestream bc differs from normal inletoulet BC Based on my readings Freestream BC freestream BC has the type inlet/outlet meaning that it looks locally (forevery face of the...

08 September 2018 1,516 0 View

How to connect between Simulink 2014a and Code Composer Studio V5?

Hi I'm working on active noise cancellation using DS TMS320C6713. I have created the model in simulink but I'm not sure how to transfer the mdl file into CCS v5.

06 July 2018 6,347 0 View

Why the hydrostatic pressure at outlet is not chaning based on velocity and total pressure?

Hi , I’m trying to model air enter high velocity from a pipe into the big rectanngle box and outlet is small nozzles from the top side of the retangle box. My boundary conditions for velocity as...

02 March 2018 3,831 3 View

How to set up domain for cfx non premixed combustion modelling?

Hi all I'm trying to remodel pool fire modelling based on this paper "LNG pool fire simulation for domino effect analysis"...

11 December 2017 1,099 2 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Regarding LBM in Boiling?

What should be the equation for halfway bounce back boundary condition for flow field with forcing term?

08 August 2024 7,938 1 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View

Hyder M. Abdul Hussein

Hi, Find the file attachment please.

Bast Regard

Ijaz Fazil Syed Ahmed Kabir

Hi Hyder I know about outflow boundary condition and how to set it via GUI,

I'm looking for how to specify it in TUI, So that I can include it in the journal file

Hi I got it

Define/boundary-conditions/outflow

Sorry I got some error while tried yesterday, now its working