How to model and simulate a small part instead of all model in ABAQUS?

08 August 2015 0 4K Report

Badges
Science topic

More Ibrahim M. Metwally's questions See All

How to accurately model Steel Fiber Concrete in ABAQUS?

How to accurately model Steel Fiber Concrete in ABAQUS? By other meaning, how to randomly distributed steel fibers inside concrete in ABAQUS?

11 December 2018 5,882 7 View

Simulate equivalent reinforced concrete in ABAQUS for simulating full scale RC structures?

Can concrete damage plasticity model in Abaqus simulate equivalent reinforced concrete by modifying its proprieties to account for the effect of steel bars (area and direction)?

05 June 2018 3,967 0 View

How to model the fragmentation of concrete due to dynamic loading in ABAQUS?

How to model the fragmentation of concrete due to dynamic loading as high velocity impact by projectile in ABAQUS?

05 June 2016 5,177 0 View

In abaqus, how to define the rate of loading on the concrete beam ?

If the concrete beam exposed to static loading in the lab at the rate of loading = .05 mm/sec., how to define this rate accurately in ABAQUS?

02 March 2016 4,416 5 View

How can I model the repaired concrete beams using epoxy injection in ABAQUS?

how to model the repaired concrete beams using epoxy injection in ABAQUS? firstly, the RC beam was loaded up to appear of first crack( 1mm width), at the middle part of the beam, this meet also...

10 November 2015 9,539 7 View

How might I model the nonlinear bond slip between steel bars and surrounding concrete by ABAQUS?

How to model the nonlinear bond slip between steel bars and surrounding concrete by ABAQUS?

06 July 2015 3,592 4 View

How do I model the nonlinear bond slip between steel bars( Truss element ) and surrounding concrete (solid element)by ABAQUS?

How to model the nonlinear bond slip between steel bars( Truss element ) and surrounding concrete (solid element)by ABAQUS? How to model the nonlinear bond slip between steel bars( Truss element )...

06 July 2015 9,104 3 View

How to accurately model Steel Fiber Concrete in ABAQUS?

OPEN DISCUSSION:- How to accurately model Steel Fiber Concrete in ABAQUS? By other meaning, how to randomly distributed steel fibers inside concrete in ABAQUS?

01 January 1970 10,115 3 View

How to export data from Sap 2000 or Etabs software to ABAQUS?

Because of modeling of skyscrapers or towers by using Abaqus is very complicated. Contrary, modeling by Etabs, Sap2000, or Revit will be more easier. Exporting data from Etabs, Sap 2000 ,...

01 January 1970 6,559 2 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Which Scopus Journal provides the most affordable fees?

"PUBLISHING IN A SCOPUS JOURNAL" Researchers are now at a cross road. The critical need to publish in a Scopus or ISI, etc journal is ever vital. Journal Publication fees must be submitted....

10 August 2024 8,621 1 View

Seeking Advice on Viability and Execution of Undergraduate Thesis Topic?

Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...

10 August 2024 8,992 0 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

Who will be moral responsible for the death of thousands of people in the event of an earthquake?

Who will bear moral responsibility for the deaths of thousands of people in the event of an earthquake? Weeks and months remain before the onset of strong earthquakes that bring death to...

08 August 2024 6,134 12 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View