How to accurately model Steel Fiber Concrete in ABAQUS?

More Ibrahim M. Metwally's questions See All

How to accurately model Steel Fiber Concrete in ABAQUS?

How to accurately model Steel Fiber Concrete in ABAQUS? By other meaning, how to randomly distributed steel fibers inside concrete in ABAQUS?

11 December 2018 5,882 7 View

Simulate equivalent reinforced concrete in ABAQUS for simulating full scale RC structures?

Can concrete damage plasticity model in Abaqus simulate equivalent reinforced concrete by modifying its proprieties to account for the effect of steel bars (area and direction)?

05 June 2018 3,967 0 View

How to model the fragmentation of concrete due to dynamic loading in ABAQUS?

How to model the fragmentation of concrete due to dynamic loading as high velocity impact by projectile in ABAQUS?

05 June 2016 5,177 0 View

In abaqus, how to define the rate of loading on the concrete beam ?

If the concrete beam exposed to static loading in the lab at the rate of loading = .05 mm/sec., how to define this rate accurately in ABAQUS?

02 March 2016 4,416 5 View

How can I model the repaired concrete beams using epoxy injection in ABAQUS?

how to model the repaired concrete beams using epoxy injection in ABAQUS? firstly, the RC beam was loaded up to appear of first crack( 1mm width), at the middle part of the beam, this meet also...

10 November 2015 9,539 7 View

How to model and simulate a small part instead of all model in ABAQUS?

07 August 2015 3,968 0 View

How might I model the nonlinear bond slip between steel bars and surrounding concrete by ABAQUS?

How to model the nonlinear bond slip between steel bars and surrounding concrete by ABAQUS?

06 July 2015 3,592 4 View

How do I model the nonlinear bond slip between steel bars( Truss element ) and surrounding concrete (solid element)by ABAQUS?

How to model the nonlinear bond slip between steel bars( Truss element ) and surrounding concrete (solid element)by ABAQUS? How to model the nonlinear bond slip between steel bars( Truss element )...

06 July 2015 9,104 3 View

How to export data from Sap 2000 or Etabs software to ABAQUS?

Because of modeling of skyscrapers or towers by using Abaqus is very complicated. Contrary, modeling by Etabs, Sap2000, or Revit will be more easier. Exporting data from Etabs, Sap 2000 ,...

01 January 1970 6,559 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View

How to get LP fiber modes directly from Comsol?

Hi there, I'm new to modelling with comsol. I would like to ask if it is possible for comsol to output linearly polarized (LP) modes? I tried modelling a simple single mode fiber with an enlarged...

23 July 2024 4,019 3 View

Sample size for qualitative study?

I am working on scale development in behavioral finance by undertaking a mixed-method approach using the exploratory sequential design. The phenomenon has diverse meanings in existing literature...

20 July 2024 9,153 11 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View