How to accurately model Steel Fiber Concrete in ABAQUS?

How to accurately model Steel Fiber Concrete in ABAQUS? By other meaning, how to randomly distributed steel fibers inside concrete in ABAQUS?

11 December 2018 5,703 7 View

Simulate equivalent reinforced concrete in ABAQUS for simulating full scale RC structures?

Can concrete damage plasticity model in Abaqus simulate equivalent reinforced concrete by modifying its proprieties to account for the effect of steel bars (area and direction)?

05 June 2018 3,819 0 View

In abaqus, how to define the rate of loading on the concrete beam ?

If the concrete beam exposed to static loading in the lab at the rate of loading = .05 mm/sec., how to define this rate accurately in ABAQUS?

02 March 2016 4,235 5 View

How can I model the repaired concrete beams using epoxy injection in ABAQUS?

how to model the repaired concrete beams using epoxy injection in ABAQUS? firstly, the RC beam was loaded up to appear of first crack( 1mm width), at the middle part of the beam, this meet also...

10 November 2015 9,429 7 View

How to model and simulate a small part instead of all model in ABAQUS?

How to model and simulate a small part instead of all model in ABAQUS?

07 August 2015 3,848 0 View

How might I model the nonlinear bond slip between steel bars and surrounding concrete by ABAQUS?

How to model the nonlinear bond slip between steel bars and surrounding concrete by ABAQUS?

06 July 2015 3,469 4 View

How do I model the nonlinear bond slip between steel bars( Truss element ) and surrounding concrete (solid element)by ABAQUS?

How to model the nonlinear bond slip between steel bars( Truss element ) and surrounding concrete (solid element)by ABAQUS? How to model the nonlinear bond slip between steel bars( Truss element )...

06 July 2015 8,933 3 View

How to accurately model Steel Fiber Concrete in ABAQUS?

OPEN DISCUSSION:- How to accurately model Steel Fiber Concrete in ABAQUS? By other meaning, how to randomly distributed steel fibers inside concrete in ABAQUS?

01 January 1970 9,911 3 View

How to export data from Sap 2000 or Etabs software to ABAQUS?

01 January 1970 6,207 2 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

What analysis to choose with a large neste dataset and clearly skewed or kurtotic distributions?

Hello! I have a dataset of n=3000 nested within 8 countries with approximately 200 or 400 responses in each country. I originally planned to perform multilevel modelling with 4 dependent variables...

02 March 2021 6,865 1 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View