Hi i want to ask that in order to find out LC 50 (96 hours) of particular toxin for fish. Should we keep the animals with food or without food?

if we expose the fish after acclimatization to particular toxin in order to find out LC 50 (96 hours).Should we keep the fish off feed or with feed for that duration. Some literature show that...

24 February 2021 357 2 View

How COVID-19 has affected mental health?

The pandemic has led to depression and anxiety and its negative effects shouldn't be ignored. However, it has also led some people to become more resilient! What do you think? Thank you.

21 February 2021 4,733 19 View

Is There are any idea to achieve H NMR signals for swollen compound ??

the samples are not completely soluble - just swelled the solvents that's mean the sample may be partially soluble any suggestion, please

16 February 2021 8,801 3 View

Pseudo random number generator in Matlab code ?

i want to implement pseudo random number generator in matlab ...i request to every one if someone have code these PRNG share with me SplitMix Permuted Congruential Generator (PCG) Random...

14 February 2021 6,828 7 View

Please ,How can I correct this kind of error?

27 January 2021 4,815 5 View

What are the standard parameter values of the commonly used classifiers?

What are the standard parameter values of the commonly used classifiers such as Support-vector machine, k-nearest neighbors, Decision tree, Random forest?

06 January 2021 6,940 7 View

PDF of a Book?

Can anyone provide me the PDF for Distributed Energy Resources in Microgrids (Integration, Challenges and Optimization)?It would be really helpful

27 December 2020 8,015 3 View

Simulation of Smart Grid?

Somepne please help me where to learn the simulation of Smart Grid on YouTube or other bookr esources?

22 December 2020 421 3 View

Doping of r-GO?

if the percentage of doping Au into rGO is too small 1~10%, is it not enough to prevent restacking of r-GO in xrd results, rGO peak appeared at 22.2 and also the peaks of gold nanoparticles so...

21 December 2020 6,091 3 View

XRD peaks for gold nanoparticles ?

is the concentration of gold salt that were added will affect on the peaks appeared. i added a very little amount of gold salt to dope graphene oxide and not all the peaks that proved the...

17 December 2020 9,275 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View