Hello,
Is there a possibility to hide the mesh on MAPDL, Im working with a very big model and showing the mesh causes ansys to crash, I don't have any geometry entities on the model (KP, Lines, Areas... etc).
Thank you.
Hello, I'm looking for a cheap commercial FEA software, it does not have to be multi physics or contains non linear simulations, all i need is an FEA soft in which we can import STEP files and...
06 July 2017 8,075 0 View
Hello, Is there any software in which we can convert the mesh files (.unv or .med) to (.inp or .msh) files? Thank you in advance
06 July 2017 2,928 0 View
Hello, i wish to know if there is any algorithme to get rid of matrix singularity. thank you.
04 May 2017 1,280 6 View
Hello, I am in my final year to get my engineering degree at numerical calculations (FEM majoratelly), i'm really confused whether investing 3 years in a PHD thesis, which can help me enhance and...
04 May 2017 3,398 3 View
Hello everyone, Is it possible to estimate the stiffness properties of a system knowing that all we have is the mass of the system and accelerations mesured by accelerometres in 3 points. thank you.
03 April 2017 2,126 3 View
Hello everyone, i'm an intern in a company that produces HVAC systems, my mission is to study the transmission of the vibrations generated by the moving parts(fans, compressor...) to the bodycar,...
02 March 2017 3,930 9 View
I'm trying to perform an harmonic analysis on Ansys with the modal superposition, i would like to know how to apply a creterion for the mode expantion depending their effectives masses, knowing...
09 October 2016 5,998 0 View
How to chose from the modal base the optimal base of mods to be exapanded depending on their effecitves modals masses for use in transient analysis with modal superposition on Ansys?
09 October 2016 5,056 4 View
is it possible to represent a flexible body by a multiple of rigide bodies (>10 bodies), this rigide bodies are attached between them by springs and dumpers so they can behave exacly like the...
01 January 1970 3,637 5 View
Hello, I have some data of accelerations in the frequency domain, I wish to get displacements explicitly from the accelerations, the problem is that I don't know exactly what should I use,...
01 January 1970 9,191 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...
27 July 2024 5,748 0 View
Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...
25 July 2024 9,058 4 View
We assume that there is a physico-statistical meaning to the constant π other than circular geometry, but the iron guardians of the Schrödinger equation deny this. The iron guardians of the...
22 July 2024 4,285 9 View
I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...
13 July 2024 3,631 4 View
I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?
09 July 2024 9,226 3 View
Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."
30 June 2024 7,894 1 View
I am modelling CFS Sheath wall in abaqus and i am applying the 100 mm displacement but i am getting high reach force close to 150 kN but i need it till 50kN. I have used mesh independent fastner...
27 June 2024 4,212 2 View