I am modelling CFS Sheath wall in abaqus and i am applying the 100 mm displacement but i am getting high reach force close to 150 kN but i need it till 50kN. I have used mesh independent fastner (asssembled fastner).
I checked your model, it has alot of things to modify. You have over constrained the model geometry.
I am trying to prepare samples for IP. The pellet size is good and I am using 1% Tx-100 and using a syringe to further lyse the cells and maintain protein-protein interactions. I keep having a...
01 August 2024 7,199 1 View
The threshold voltage (Vth) of a MOS device plays a crucial role for its operation. At the same time, noise is an intrinsic factor. So how noise (flicker or thermal) change with the change in...
29 July 2024 3,246 0 View
Dear all, I have noticed, as the ZnO content increases, the Raman intensity at 100cm-1 also increases. However, there is a peak nearby at 130 cm-1, which I could not find in any paper related to...
28 July 2024 5,410 1 View
If you don't understand my question let me know
21 July 2024 563 1 View
I am working on scale development in behavioral finance by undertaking a mixed-method approach using the exploratory sequential design. The phenomenon has diverse meanings in existing literature...
20 July 2024 9,153 11 View
I need to convert Available phosphorus into total phosphorus
18 July 2024 6,799 3 View
Bioinformatics tools like peptide cutter
15 July 2024 6,453 1 View
The burden of obesity is enormous. The greater challenge lies in accurately diagnosing obesity at the right time, reflecting the true increase in visceral fat. BMI may not accurately represent...
14 July 2024 8,771 4 View
How does high humidity affect the growth and development of crops?
10 July 2024 7,258 20 View
In what ways does high humidity impact the pollination process in agricultural plants?
10 July 2024 7,513 13 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...
30 July 2024 7,062 1 View
I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...
29 July 2024 9,572 3 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View
hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...
20 July 2024 647 2 View
Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...
17 July 2024 1,501 1 View
I saw a paper(PHAN V-T, ZHANG X, LI Y, et al. Microscale modeling of creep deformation and rupture in Nickel-based superalloy IN 617 at high temperature [J]. Mechanics of Materials, 2017, 114:...
16 July 2024 8,436 0 View
Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...
15 July 2024 3,491 0 View