Hi there,
Center of Gravity Location is a parameter accessible in the 'Dynamic Mesh Zones' window inside the Fluent. I'd like to know what's the command to get "center of gravity location" in a UDF?
Thanks
Hi,
Name (Arguments): DT_CG(dt)
Argument Type: Dynamic_Thread *dt
(The argument dt is a pointer to the dynamic thread structure )
This returns center of gravity vector.
I'm using VOF in Fluent to simulate impact of a falling droplet onto a solid particle in mid-air (pls see the picture). Instead of using a constant contact angle (CA), I want to apply a dynamic CA...
09 October 2017 1,537 2 View
Using VOF ith a laminar model, I'm simulating collision of a droplet and a spherical particle. The particle moves very fast (~7 m/s) and so penetrates into the falling droplet and deforms it to a...
04 May 2017 7,589 3 View
In a droplet impact onto a stationary particle, I want to calculate mass conservation of VOF method (before impact vs. after impact ends). For that, I use Reports => Volume Integrals window. In...
02 March 2017 5,338 7 View
I'm simulating droplet impact onto a moving particle (axisymmetric VOF+6DOF in dynamic mesh). I tried to increase the particle mass in UDF by a factor of 1000 (for the same particle size). But, as...
31 December 2016 6,384 7 View
For simulating a droplet collision onto a moving particle, I use a semi-circle as my particle in an axisymmetric solution. However, I don't have just one line as the 'axis' of domain and particle...
31 December 2016 9,162 6 View
I want to do an axisymmetric simulation of a head-on collision between a falling droplet and a spherical particle. However, as you can see in the attached figure, dynamic mesh fails to follow the...
31 December 2016 5,557 11 View
For simulating a droplet and particle collision, I assigned particle mass using 6DOF below and I defined particle velocity with 'Centre of Gravity Velocity' in 'dynamic mesh' window. As figure...
11 December 2016 8,132 8 View
I'm simulating a particle collision onto a droplet in Fluent (attached Fig.). Particle is defined as a 'wall' and when I'm using 'Dynamic Mesh' with 'C.G. Vel= -6', the simulation runs well....
11 December 2016 4,473 0 View
I have a particle and a droplet both of them are moving to collide together. Therefore, I need to assign a mass to the particle as momentum of impact matters very much. I'm using a UDF for...
11 December 2016 3,667 3 View
I'm simulating collision of a droplet and a moving particle in mid-air. The particle is launched towards the droplet while the drop is moving in opposite direction (pls. see Fig. 1)For solving...
10 November 2016 9,319 3 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...
03 August 2024 3,371 3 View
I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?
02 August 2024 3,143 4 View
Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out? For example consider a process for certain product manufacture where a new process flow...
31 July 2024 781 1 View
Dear All Gromacs User I would like to restart MD without using checkpint .cpt files? I heard there is a way for acheiveing this. Any input and sugegstions are most welcome. Thanking You Budheswar
29 July 2024 3,084 8 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
If I want to calculate molecular dynamics (Gromacs), do I first need to optimize the geometry of the molecule? For example, I first draw the molecule in Avogadro, and then what? I guess I can't...
28 July 2024 673 3 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...
25 July 2024 2,309 5 View
Hello, I'm trying to create parameter and coordinate files for a drug (PRG-A01) found on the following page: http://www.probechem.com/products_PRG-A01.html I used the guide made by Michael...
17 July 2024 3,472 3 View