What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

What is the indication of the absence of peaks in Methanol electrooxidation CV curves ?

I have several question regarding the MOR; hope anyone help me better understand. 1- in CV using (KOH+MEOH) what is the indication of absence of the redox peaks? shouldn't they exist as a sign...

28 February 2021 4,851 8 View

Is There are any idea to achieve H NMR signals for swollen compound ??

the samples are not completely soluble - just swelled the solvents that's mean the sample may be partially soluble any suggestion, please

16 February 2021 8,801 3 View

Is there association of SARS-CoV-2 infection rate with meteorological factors?

There are contradictory research papers about the correlation between meteorological parameters and incidence of COVID-19 in some countries worldwide. Is there correlation between the...

15 February 2021 5,806 2 View

Why does the band sizes on Agarose gel electrophoresis differ from the peaks at capillary electrophoresis?

14 February 2021 4,773 4 View

What is the best way to do symmetry in ANSYS Fluent for flow between two concentric cylinders ?

I am working on Taylor Couette flow between concentric cylinders and the results are correct for the full case. however, I wanted to do symmetry case to improve the mesh. I have tried periodic...

11 February 2021 2,193 6 View

What is the success rate of the e-learning plan in achieving the objectives of the curricula?

I need to know the reliability of the evaluation results and the rate of achievement of the course objectives, Thank you (*-*).

02 February 2021 7,828 7 View

What is the success rate of the e-learning program in your country during the time of Covid-19?

I need to know the extent of the success of the e-learning plan in countries of different capabilities, Thank you (*-*)

02 February 2021 4,712 15 View

How can I get good bands by silver nitrate staining on SSCP method?

Hi Dear colleagues This was my first experience on SSCP, and I couldn`t get any band by silver staining! Staining with Et Br was successful. I mixed the PCR product with formamide loading dye,...

01 February 2021 8,788 6 View

How to calculate the Boiling point for metals at high vapor pressure?

In our experiment, some metal surfaces are exposed to radiation heat under high vapor gas pressure. I would like to ask if there is any way to calculate the boiling point for metals under high...

31 January 2021 249 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View