Users of Ansys Fluent
I suggest you follow https://skill-lync.freshdesk.com/support/solutions/articles/43000583840-introduction-to-meshing-and-inserting-a-method-in-ansys
thank you very much Muhammad Ali, it's so helpful
So important Shawon Bhattacharjee, thank you for your help.
In my case I try to simulate a heat transfer on the solar receiver tube, that possessed a tube with an exchanger inside. The length is 1.8m and the diameter is 0.06m.
It's so helpful Mr Shawon Bhattacharjee , thank you very much for your advices
Hi, If you show some pictures of the geometry, we can help you better.
Hi,
It depends on the studied geometry, I see that the hexa mesh with finer mesh near the wall is the best.
Thank you Mr. Ashkan Ghafari i will chare with you some pictues of the Geom
I have a response variable called skin yellowness, which I will measure via a scored color chart, whereby 1 is pale yellow and 15 is orange. I'm not sure if this counts as an ordinal variable,...
11 August 2024 4,792 1 View
Approximate concentrations are require in compared with the WHO permissible limts
11 August 2024 2,723 1 View
how can I read Waters, R. S. 1958. Morphological mapping. Geography 43 :10-17 from internet? note: not in google or resaearch gate
26 July 2024 7,813 3 View
How can the rubber fibres produced by the electrospinning device be removed from the fibre collector (aluminium foil) without affecting the orientation of the rubber fibres for use in reinforcing...
26 July 2024 8,281 0 View
Despite not having cells in the media, I am getting purple color. I have tried many troubleshooting methods, varying media types, and even different MTTs from different companies to figure out the...
21 July 2024 9,913 1 View
As PhD student specialized as food and industrial microbiology need to further research on bacteriocin and fermented food.
16 July 2024 7,394 1 View
What are some of the areas to consider in undertaken research in educational administration in MPhil.
14 July 2024 8,394 2 View
XRD analysis
08 July 2024 977 4 View
how i can calculate mathematically COD concentration if i add 1gr from glucose to 1 L distilled water
08 July 2024 9,103 2 View
Previously, I successfully modelled the transmission and reflection of electromagnetic waves incident on non-magnetic materials. Please refer to my publications for details: 1- A polynomial model...
05 July 2024 1,396 2 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...
27 July 2024 5,747 0 View
Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...
25 July 2024 2,308 5 View
Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...
25 July 2024 9,058 4 View
We assume that there is a physico-statistical meaning to the constant π other than circular geometry, but the iron guardians of the Schrödinger equation deny this. The iron guardians of the...
22 July 2024 4,285 9 View
"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...
13 July 2024 8,620 5 View
Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....
07 July 2024 1,181 8 View
hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.
03 July 2024 5,418 4 View
Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."
30 June 2024 7,894 1 View
I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...
26 June 2024 2,358 0 View