ABAQUS OR ANSYS
MY CHOICE IS ANSYS
I wanna know the procedure to generate loading and load spectrum?
31 December 2018 2,379 4 View
i need the values for IS11513 material. What is the young's modulus, poisson ratio, its yield strength and plastic strain.
08 September 2018 9,933 0 View
I am doing analysis in abaqus explicit so i needed the plastic property i found the initial value yield stress-830 N/mm2 plastic strain-0 i need the next value to proceed the analysis further
08 September 2018 5,570 5 View
i have run bolt load in abaqus implicit/standard then i imported this output to explicit but deformation created due to bolt load is not showing so i needed to apply bolt load in explicit but i...
07 August 2018 1,188 0 View
is there any relationship equation between stress and strength
06 July 2018 864 8 View
after welding hardness decreases in the sequence weld zone--------->heat affected zone ------------>base metal what happens to strength? in what sequence strength varies ?
06 July 2018 6,982 5 View
for non linear analysis in abaqus
06 July 2018 9,994 0 View
just best electron that will withstand high torque after welding
06 July 2018 2,155 6 View
what is the experimental method to find the HAZ (heat affected zone) in welded pipe (pipe weld)
05 June 2018 1,139 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...
13 July 2024 3,631 4 View
I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?
09 July 2024 9,226 3 View
Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."
30 June 2024 7,894 1 View
Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...
25 June 2024 4,286 4 View
I am trying the simulate the drum brake squeal in ansys. For giving the rotational velocity to drum what should i use the Rotational velocity or CMROTATE command.
24 June 2024 5,125 0 View
I need to get the eigenvalues after a modal analysis in ansys workbench. Is there any next APDL command that will get the required result.
20 June 2024 1,668 0 View
Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...
14 June 2024 6,480 0 View
