How to find HAZ (heat affected zone ) experimentally?

Surendran .R @Surendran_r3

06 June 2018 0 1K Report

what is the experimental method to find the HAZ (heat affected zone) in welded pipe (pipe weld)

Badges
Science topic

Similar topics
Heat

More Surendran .R's questions See All

How to generate load spectrum in fe safe?

I wanna know the procedure to generate loading and load spectrum?

31 December 2018 2,191 4 View

What is mechanical properties of IS11513 steel?

i need the values for IS11513 material. What is the young's modulus, poisson ratio, its yield strength and plastic strain.

08 September 2018 9,816 0 View

What is plastic property of M8 10.9 grade bolt?

I am doing analysis in abaqus explicit so i needed the plastic property i found the initial value yield stress-830 N/mm2 plastic strain-0 i need the next value to proceed the analysis further

08 September 2018 5,325 5 View

How to apply bolt load in abaqus explicit?

i have run bolt load in abaqus implicit/standard then i imported this output to explicit but deformation created due to bolt load is not showing so i needed to apply bolt load in explicit but i...

07 August 2018 1,025 0 View

For non-linear analysis which software is best to use(ABAQUS OR ANSYS)?

ABAQUS OR ANSYS

06 July 2018 3,570 1 View

How to calculate strength of the material after welding by stress?

is there any relationship equation between stress and strength

06 July 2018 744 8 View

What is effect of hardness vs strength in weld joint?

after welding hardness decreases in the sequence weld zone--------->heat affected zone ------------>base metal what happens to strength? in what sequence strength varies ?

06 July 2018 6,875 5 View

What is meant by johnson cook model , exactly...?

for non linear analysis in abaqus

06 July 2018 9,867 0 View

What is best electrode for CO2-MIG WELDING of steel pipe?

just best electron that will withstand high torque after welding

06 July 2018 2,032 6 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

Is the a way to contol flow (Flow velocity) without impacting pressure value?

I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?

25 February 2021 7,187 3 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View

What kind of steel moulds are used for hot pressing metal powders?

My main concern is that the metal powders should not weld to the mold surface and I should easily be able to eject out the pressed samples. I am looking for alternative for graphite moulds. The...

22 February 2021 2,965 4 View