What is mechanical properties of IS11513 steel?

i need the values for IS11513 material. What is the young's modulus, poisson ratio, its yield strength and plastic strain.

08 September 2018 9,816 0 View

What is plastic property of M8 10.9 grade bolt?

I am doing analysis in abaqus explicit so i needed the plastic property i found the initial value yield stress-830 N/mm2 plastic strain-0 i need the next value to proceed the analysis further

08 September 2018 5,325 5 View

How to apply bolt load in abaqus explicit?

i have run bolt load in abaqus implicit/standard then i imported this output to explicit but deformation created due to bolt load is not showing so i needed to apply bolt load in explicit but i...

07 August 2018 1,025 0 View

For non-linear analysis which software is best to use(ABAQUS OR ANSYS)?

ABAQUS OR ANSYS

06 July 2018 3,570 1 View

How to calculate strength of the material after welding by stress?

is there any relationship equation between stress and strength

06 July 2018 744 8 View

What is effect of hardness vs strength in weld joint?

after welding hardness decreases in the sequence weld zone--------->heat affected zone ------------>base metal what happens to strength? in what sequence strength varies ?

06 July 2018 6,875 5 View

What is meant by johnson cook model , exactly...?

for non linear analysis in abaqus

06 July 2018 9,867 0 View

What is best electrode for CO2-MIG WELDING of steel pipe?

just best electron that will withstand high torque after welding

06 July 2018 2,032 6 View

How to find HAZ (heat affected zone ) experimentally?

what is the experimental method to find the HAZ (heat affected zone) in welded pipe (pipe weld)

05 June 2018 1,032 0 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View