What is mechanical properties of IS11513 steel?

09 September 2018 0 10K Report

i need the values for IS11513 material. What is the young's modulus, poisson ratio, its yield strength and plastic strain.

Badges
Science topic

More Surendran .R's questions See All

How to generate load spectrum in fe safe?

I wanna know the procedure to generate loading and load spectrum?

31 December 2018 2,379 4 View

What is plastic property of M8 10.9 grade bolt?

I am doing analysis in abaqus explicit so i needed the plastic property i found the initial value yield stress-830 N/mm2 plastic strain-0 i need the next value to proceed the analysis further

08 September 2018 5,570 5 View

How to apply bolt load in abaqus explicit?

i have run bolt load in abaqus implicit/standard then i imported this output to explicit but deformation created due to bolt load is not showing so i needed to apply bolt load in explicit but i...

07 August 2018 1,188 0 View

For non-linear analysis which software is best to use(ABAQUS OR ANSYS)?

ABAQUS OR ANSYS

06 July 2018 3,694 1 View

How to calculate strength of the material after welding by stress?

is there any relationship equation between stress and strength

06 July 2018 864 8 View

What is effect of hardness vs strength in weld joint?

after welding hardness decreases in the sequence weld zone--------->heat affected zone ------------>base metal what happens to strength? in what sequence strength varies ?

06 July 2018 6,982 5 View

What is meant by johnson cook model , exactly...?

for non linear analysis in abaqus

06 July 2018 9,994 0 View

What is best electrode for CO2-MIG WELDING of steel pipe?

just best electron that will withstand high torque after welding

06 July 2018 2,155 6 View

How to find HAZ (heat affected zone ) experimentally?

what is the experimental method to find the HAZ (heat affected zone) in welded pipe (pipe weld)

05 June 2018 1,139 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Can't spin-orbit coupling(SOC) be included in optical properties calculation in CASTEP?

I am currently using CASTEP version 2020. When I want to run optical properties calculations with spin-orbit coupling(SOC), I encounter the following error in a pop-up window before the job gets...

02 August 2024 2,890 0 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

Water Consumption in Plastic Recycling: Is it Higher Than for Virgin Plastics?

Hello, dear colleagues, I would like your help in finding a reference that provides an average water savings due to plastic recycling compared to the consumption of virgin materials, preferably...

29 July 2024 4,630 0 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Can you recommend provider Intermediate laboratory test for hydrocarbon, polyethylene & polypropylene?

Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...

25 July 2024 8,108 0 View