How to apply bolt load in abaqus explicit?

Surendran .R @Surendran_r3

08 August 2018 0 1K Report

i have run bolt load in abaqus implicit/standard

then i imported this output to explicit but deformation created due to bolt load is not showing

so i needed to apply bolt load in explicit but i cant

can anyone help me

Badges
Science topic

More Surendran .R's questions See All

How to generate load spectrum in fe safe?

I wanna know the procedure to generate loading and load spectrum?

31 December 2018 2,379 4 View

What is mechanical properties of IS11513 steel?

i need the values for IS11513 material. What is the young's modulus, poisson ratio, its yield strength and plastic strain.

08 September 2018 9,933 0 View

What is plastic property of M8 10.9 grade bolt?

I am doing analysis in abaqus explicit so i needed the plastic property i found the initial value yield stress-830 N/mm2 plastic strain-0 i need the next value to proceed the analysis further

08 September 2018 5,570 5 View

For non-linear analysis which software is best to use(ABAQUS OR ANSYS)?

ABAQUS OR ANSYS

06 July 2018 3,694 1 View

How to calculate strength of the material after welding by stress?

is there any relationship equation between stress and strength

06 July 2018 864 8 View

What is effect of hardness vs strength in weld joint?

after welding hardness decreases in the sequence weld zone--------->heat affected zone ------------>base metal what happens to strength? in what sequence strength varies ?

06 July 2018 6,982 5 View

What is meant by johnson cook model , exactly...?

for non linear analysis in abaqus

06 July 2018 9,994 0 View

What is best electrode for CO2-MIG WELDING of steel pipe?

just best electron that will withstand high torque after welding

06 July 2018 2,155 6 View

How to find HAZ (heat affected zone ) experimentally?

what is the experimental method to find the HAZ (heat affected zone) in welded pipe (pipe weld)

05 June 2018 1,139 0 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

AUX gas reading problem on QE with full MS and PRM method in one run?

Dear QE-users, In the method where full MS positive mode and PRM mode are used, we always get an incorrect auxiliary gas reading (41 instead of 25). This only happens in this method; other...

06 August 2024 4,953 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

People weight in Oaxaca Blinder Decomposition on R?

Hello guys! Do you have experience running a Oaxaca-Blinder decomposition on R applying person weights. How do you suggest doing it? I have a variable PERWT which gives more information on how...

04 August 2024 6,033 0 View

How to perform EEG source analysis on each trial of data separately?

Hello Everyone I have a question about structure for connectivity analysis on sources. My goal: preprocess and cut data into trials create headmodels, using template MRI file perform source...

30 July 2024 2,744 1 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

How to add Cr parameter in autodock?

When I run autogrid4 it says: autogrid4: ERROR: Unknown receptor type: "Cr" -- Add parameters for it to the parameter library first! Look forward to your reply.Thank you so much!

29 July 2024 488 0 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View