Does anyone know DEFINE_CONTACT udf for dynamic mesh in ansys fluent?

03 December 2021 1 7K Report

I'm trying to do a simulation with two walls intersecting and merging, but instead they are passing each other like in the gif

Erfan Rahimi

Hello!

See the following links:

1- https://www.youtube.com/watch?v=-PwFOiGM6MU

2- https://www.youtube.com/watch?v=fbaV_knzzks

3- https://www.youtube.com/watch?v=aFZINnSeiwE

Badges
Science topic

More Matheus Sampaio's questions See All

Absorption coefficient of methane?

Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?

06 August 2024 980 5 View

How are Large Models Exploring and Outputting Knowledge Understanding in Specific Content Areas, and What Does Academic Research Say About It?

Hello everyone！ I am currently exploring the performance of large models in understanding knowledge in specific domains, and attempting to construct a knowledge framework similar to what...

05 August 2024 5,729 2 View

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity?

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...

03 August 2024 5,358 0 View

How do i get an account to upload my published papers?

need to open an account to upload my published papers

01 August 2024 9,255 1 View

What is the problem with these tissue culture plants?

All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.

01 August 2024 589 4 View

How to correctly use the UTE and ZTE pulse sequences in Bruker's ParaVision software?

I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...

01 August 2024 9,227 1 View

Is artifacts in XPS possible to build high deviation in binding energy larger than 5 eV??

Hello. Thanks for your consideration to see my question. Recently, I conducted XPS anaylsis of g-CN that is prepared from thermal polycondensation of DCDA, so-called conventional bulk-g-CN,...

30 July 2024 9,824 2 View

Which statistical test should we use?

N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.

30 July 2024 7,233 4 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

Can the limit of quantification (LOQ) of an analytical method fall outside its linear dynamic range, or must it always be within it?

Can an analytical method's limit of quantification (LOQ) be outside its linear dynamic range, or is it always required to be within it? Please provide a thorough explanation supported by verified...

29 July 2024 7,198 9 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View

Why i can't get access to isosurface in fluent?

hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.

03 July 2024 5,418 4 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View