Does any one knows about Elliptic Blending Reyonlds stress Model in Ansys Fluent?

More Sujit Mishra's questions See All

How to obtained Velocity profiles for ahmed body?

Can any one tell me how to create the velocity profile shown below: Every paper used to published and explain clearly. But i am unable to create the velocity profile. i use Microsoft excel and...

01 February 2020 4,812 2 View

Can i know the proper procedure to be followed to mesh the cfd modeling of a car in ansys fluent ?

i am working on Ansys fluent last 3 months to get the drag coefficient of my car model .i had problem with find the proper mesh . i already try with edge meshing and auto mesh with inflation...

01 January 1970 9,942 0 View

How ahmed body is similar to diffrent car body shapes

researchers used Ahmed model for the investigation of various numerical investigation to reduce the drag of the vehicle with different slant angles.how far the Ahmed body is similar to a standard...

01 January 1970 9,584 3 View

Can any one suggest me a good comfrugraton to run ansys fluent 15 .the minimum requirements to solve a research problem in fluent .?

WHAT WILL BE THE PROCESSOR /RAM/SPEED/HARD DISK ETC...

01 January 1970 8,565 3 View

What The Best Computer Specification To Get The Mesh Generation With Optimum Speed Of 150 Million Nodes In Ansys Fluent?

BEST CONFRUGATION

01 January 1970 3,698 3 View

Can i know from you about can we simulate wind turnnel test to do cfd analysis over a car bodies?

simulating wind tunnel test software required to know about the drag and lift factors over a vehicle.

01 January 1970 635 4 View

Posthoc test lettering in JAMOVI?

Does anyone know of a module for the JAMOVI software that is capable of generating mean separations using the classic letters based on post hoc results (e.g., Tukey test)? If, as I believe, such...

31 July 2024 3,333 4 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View

Why i can't get access to isosurface in fluent?

hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.

03 July 2024 5,418 4 View

What separates a human employee from an AI employee?

I want to know how AI employee will be different from a human employee who has no time to work because he has a family to manage?

01 July 2024 4,827 6 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to converge PEMFC in Ansys Fluent?

I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...

26 June 2024 2,358 0 View

What is the exact mathematical formulae and the C++ code of EMMS drag model that is used and applied in ANSYS Fluent 2023?

EMMS - Energy Minimization Multi-Scale

18 June 2024 5,857 2 View

How to compile a udf in Fluent to import hourly weather data and update the boundary condition based on it ?

Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...

14 June 2024 6,480 0 View