How to obtained Velocity profiles for ahmed body?

Can any one tell me how to create the velocity profile shown below: Every paper used to published and explain clearly. But i am unable to create the velocity profile. i use Microsoft excel and...

01 February 2020 4,692 2 View

Does any one knows about Elliptic Blending Reyonlds stress Model in Ansys Fluent?

How to get Elliptic Blending Reyonlds stress Model in Ansys fluent. i am using aerodynamic flow over sedan car to estimate drag and separations zones near the wall. how this model can i use in...

05 June 2019 1,734 3 View

Can any one suggest me a good comfrugraton to run ansys fluent 15 .the minimum requirements to solve a research problem in fluent .?

WHAT WILL BE THE PROCESSOR /RAM/SPEED/HARD DISK ETC...

01 January 1970 8,459 3 View

Can i know the proper procedure to be followed to mesh the cfd modeling of a car in ansys fluent ?

i am working on Ansys fluent last 3 months to get the drag coefficient of my car model .i had problem with find the proper mesh . i already try with edge meshing and auto mesh with inflation...

01 January 1970 9,824 0 View

How ahmed body is similar to diffrent car body shapes

researchers used Ahmed model for the investigation of various numerical investigation to reduce the drag of the vehicle with different slant angles.how far the Ahmed body is similar to a standard...

01 January 1970 9,496 3 View

Can i know from you about can we simulate wind turnnel test to do cfd analysis over a car bodies?

simulating wind tunnel test software required to know about the drag and lift factors over a vehicle.

01 January 1970 544 4 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View