Can any one suggest me a good comfrugraton to run ansys fluent 15 .the minimum requirements to solve a research problem in fluent .?

More Sujit Mishra's questions See All

How to obtained Velocity profiles for ahmed body?

Can any one tell me how to create the velocity profile shown below: Every paper used to published and explain clearly. But i am unable to create the velocity profile. i use Microsoft excel and...

01 February 2020 4,812 2 View

Does any one knows about Elliptic Blending Reyonlds stress Model in Ansys Fluent?

How to get Elliptic Blending Reyonlds stress Model in Ansys fluent. i am using aerodynamic flow over sedan car to estimate drag and separations zones near the wall. how this model can i use in...

05 June 2019 1,813 3 View

Can i know the proper procedure to be followed to mesh the cfd modeling of a car in ansys fluent ?

i am working on Ansys fluent last 3 months to get the drag coefficient of my car model .i had problem with find the proper mesh . i already try with edge meshing and auto mesh with inflation...

01 January 1970 9,942 0 View

How ahmed body is similar to diffrent car body shapes

researchers used Ahmed model for the investigation of various numerical investigation to reduce the drag of the vehicle with different slant angles.how far the Ahmed body is similar to a standard...

01 January 1970 9,584 3 View

What The Best Computer Specification To Get The Mesh Generation With Optimum Speed Of 150 Million Nodes In Ansys Fluent?

BEST CONFRUGATION

01 January 1970 3,698 3 View

Can i know from you about can we simulate wind turnnel test to do cfd analysis over a car bodies?

simulating wind tunnel test software required to know about the drag and lift factors over a vehicle.

01 January 1970 635 4 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out?

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out? For example consider a process for certain product manufacture where a new process flow...

31 July 2024 781 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

How to restart MD without using checkpint file in GROMACS?

Dear All Gromacs User I would like to restart MD without using checkpint .cpt files? I heard there is a way for acheiveing this. Any input and sugegstions are most welcome. Thanking You Budheswar

29 July 2024 3,084 8 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

Thokchom Subhaschandra Singh

I would recommend a mini workstation with high end processor, minimum 16GB RAM with cache memory equal to or more than 3MB. A 100GB free memory would do fine as far as HDD is concerned. A clock speed of 3.2 GHz or more is suggested.

An UPS is strongly recommended before initialising the analysis for uninterrupted supply of power

Ketan Ajay

You require minimum of 16 GB ram ,,, and a clock speed of 3.2 GHz

Sujit Mishra

thank you for your suggestion