There is no explanation written in header files and there seem to be useful macros such as those in neighbour.h header files.
InsyAllah I will explain in detail soon.
WHy not right now dear ? I am waiting to hear what you will explain later on. Please do it here itself.
Dear All, I have no idea about DVDWT except that it is a diffuse interface model. I want to know pros and cons of using it over standard free surface models such as CLSVOF ? I was going through a...
02 March 2015 2,057 2 View
Dear All, I am facing trouble handling convective flux in a scalar transport equation for two-phase flow along wall boundary. Some wall boundary cells have low density and viscosity while the rest...
31 December 2014 3,934 12 View
I have a set of data which each time instant varies with x and y location and then also varies over time periodically. I wish to average this dataset over the period. Can someone suggest how to do it?
03 April 2014 7,938 5 View
I am trying to simulate evaporation in unsaturated porous wicks. I have run two set of simulations with different geometries and have incorporated symmetry B.C inside porous region. But behavior...
01 February 2014 8,185 3 View
I was wondering if it is possible to make the gas phase flow in a one way direction in porous media by some artificial means.
31 December 2013 1,007 2 View
Can someone suggest some open-source softwares for modelling two-phase flow in porous media? I was trying to use FLUENT but it is not working well.
11 December 2013 1,687 7 View
Any reference paper or hint would be of great help. I wish to model capillary force term in porous wick. But am unable to do so as I am not aware of how to implement it. Should we modify...
10 November 2013 356 3 View
I am well aware of Rudman algorithm's implementation in 2D cases. But how to go for 3D? Should we just have one more case for z-direction advection? or anything special?
10 November 2013 231 2 View
I wish to do 3D boiling simulation using VOF model. For that I need to know the direction split algorithm in 3D on cartesian grids. Also I need to use the least squares volume-of-fluid interface...
10 November 2013 7,980 4 View
During heat leak to the compensation chamber (CC) in LHP, is it possible for vapor to have leaked to CC? In a recent paper on bubble dynamics inside an idealized porous wick by Ram Ranjan et...
10 November 2013 3,701 5 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...
25 July 2024 2,309 5 View
I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...
13 July 2024 3,631 4 View
"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...
13 July 2024 8,621 5 View
I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?
09 July 2024 9,226 3 View
Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....
07 July 2024 1,182 8 View
hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.
03 July 2024 5,418 4 View
Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."
30 June 2024 7,894 1 View