How to model capillary force term in unsaturated porous media at liquid-vapor interface ?

More Bharat bhushan Sharma's questions See All

Which one is better - dynamic van der waals theory(DVDWT) or CLSVOF for free surface flow ?

Dear All, I have no idea about DVDWT except that it is a diffuse interface model. I want to know pros and cons of using it over standard free surface models such as CLSVOF ? I was going through a...

02 March 2015 1,950 2 View

How should I treat the convective term at the boundary for high density and viscosity ratio two phase flow?

Dear All, I am facing trouble handling convective flux in a scalar transport equation for two-phase flow along wall boundary. Some wall boundary cells have low density and viscosity while the rest...

31 December 2014 3,793 12 View

Can anyone help with space and time averaged scattered data?

I have a set of data which each time instant varies with x and y location and then also varies over time periodically. I wish to average this dataset over the period. Can someone suggest how to do it?

03 April 2014 7,843 5 View

What is a suitable Symmetry Boundary Condition for two-phase flow inside porous media?

I am trying to simulate evaporation in unsaturated porous wicks. I have run two set of simulations with different geometries and have incorporated symmetry B.C inside porous region. But behavior...

01 February 2014 8,064 3 View

Is it is possible to ensure unidirectional flow of gas phase in porous media by some means?

I was wondering if it is possible to make the gas phase flow in a one way direction in porous media by some artificial means.

31 December 2013 916 2 View

Software for two-phase flow in porous media which solves full navier stokes equation?

Can someone suggest some open-source softwares for modelling two-phase flow in porous media? I was trying to use FLUENT but it is not working well.

11 December 2013 1,569 7 View

3D VOF simulation?

I wish to do 3D boiling simulation using VOF model. For that I need to know the direction split algorithm in 3D on cartesian grids. Also I need to use the least squares volume-of-fluid interface...

10 November 2013 7,875 4 View

How do we use Rudman direction split algorithm for 3-Dimensional interfacial flow ?

I am well aware of Rudman algorithm's implementation in 2D cases. But how to go for 3D? Should we just have one more case for z-direction advection? or anything special?

10 November 2013 133 2 View

How to deposit a layer of nanoparticles of definite and controlled thickness?

I wish to deposit CNT and Cu nanoparticles over a sintered Cu microporous wick and wish to maintain controlled thickness. Any suggestions or link related this is most welcome.

10 November 2013 9,179 20 View

Can vapor penetrate through porous wick to the compensation chamber in loop heat pipes (LHPs)?

During heat leak to the compensation chamber (CC) in LHP, is it possible for vapor to have leaked to CC? In a recent paper on bubble dynamics inside an idealized porous wick by Ram Ranjan et...

10 November 2013 3,609 5 View

How to code open-ended questions in SPSS?

Hello all, In SPSS I am going to code 2 open-ended questions. I have already read all the answers and I made a list of the most important categories to which I can code the answers. This question...

02 March 2021 1,757 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Alexander J. Babchin

We discuss here the Capillary Pressure in Poropus Media, as a function of SATURATION. I can refer you, Brahat, to my shirt paper on the subject, published in TRANSPORT in POROPUS MEDIA, 2006. The text of this paper is posted on my RG site.

Bharat bhushan Sharma

Thanks for your reply Dr. Babchin and papers. I will go through your papers.

Kind Regards,

Bharat

Bharat, for your convinience I attached the file right here.