Can any one help me to get melting and boiling temperature of cr 39 polymer?

i need to simulate laser ablation of Allyl digycol carbonate (ADC) or cr39 and in order to do that i need boiling and melting temperature of that polymer Thsnk you

11 December 2016 1,141 0 View

How i can calculate deposition coverage area if i have deposition diameter?

10 November 2016 8,008 3 View

Where i can find raman spectrometer in tehran universities ?

07 August 2016 3,103 0 View

What is possible cell culturing application for laser induced periodic surface structure on polymer?

laser induced periodic surface structure for cell culturing

06 July 2016 5,854 1 View

By using ansys,i simulated a grooves on a dielectric surface,how i can calculate surface roughness using ansys ?

how i can calculate surface roughness using ansys?

08 September 2015 6,244 1 View

By using ansys, how i can model laser heat source??

By using ansys,How i can model laser heat source??

06 July 2015 9,946 0 View

How i can simulate laser ablation by comsol multiphysics?

how i can simulate femtosecond laser ablation on a dielectric substrate using comsol multiphysics

04 May 2015 6,700 1 View

Can I simulate surface enhanced raman scattering using ANSYS multiphysics?

Regarding sers biosensor, can I simulate it in ANSYS?

04 May 2015 6,083 1 View

Can i simulate surface enhancement raman scattering by comsol multiphysics?

sers layer over a dielectric surface in order to get a biosensor

03 April 2015 8,314 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How can I make stacked bar graph with scatter plot?

I want to make a stacked bar graph with showing each data value as dots. I tried with graph pad prism, version 6, but could not succeed. Does anyone have tried before making such graphs?

01 March 2021 9,383 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View