By using ansys,i simulated a grooves on a dielectric surface,how i can calculate surface roughness using ansys ?

09 September 2015 1 6K Report

how i can calculate surface roughness using ansys?

Refer this link:http://www.linkedin.com/grp/post/66032-5791845951823958016

Refer this link:https://web.fe.up.pt/~em00021/eramus/project_english.pdf

Refer this link:http://www.ansys.com/staticassets/ANSYS/staticassets/resourcelibrary/confpaper/2006-Int-ANSYS-Conf-256.pdf

Badges
Science topic

More Rana Taha's questions See All

Can any one help me to get melting and boiling temperature of cr 39 polymer?

i need to simulate laser ablation of Allyl digycol carbonate (ADC) or cr39 and in order to do that i need boiling and melting temperature of that polymer Thsnk you

11 December 2016 1,198 0 View

How i can calculate deposition coverage area if i have deposition diameter?

If i deposit a layer of thiophenol on a gold surface,how i can calculate average coverage area if i get a circle deposit layer and i measured its radius

10 November 2016 8,095 3 View

Where i can find raman spectrometer in tehran universities ?

In any university in tehran , can i find a raman spectrometer?

07 August 2016 3,169 0 View

What is possible cell culturing application for laser induced periodic surface structure on polymer?

laser induced periodic surface structure for cell culturing

06 July 2016 5,912 1 View

Can i simulate surface enhancement raman scattering using ansys and if it is possible?

sers in ansys

09 October 2015 1,320 0 View

By using ansys, how i can model laser heat source??

By using ansys,How i can model laser heat source??

06 July 2015 10,009 0 View

How i can simulate laser ablation by comsol multiphysics?

how i can simulate femtosecond laser ablation on a dielectric substrate using comsol multiphysics

04 May 2015 6,824 1 View

Can I simulate surface enhanced raman scattering using ANSYS multiphysics?

Regarding sers biosensor, can I simulate it in ANSYS?

04 May 2015 6,143 1 View

Can i simulate surface enhancement raman scattering by comsol multiphysics?

sers layer over a dielectric surface in order to get a biosensor

03 April 2015 8,367 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

When I simulate for S parameters using ADS, I have faced this issue that I have attached. Please anyone clarify me?

...

31 July 2024 1,671 3 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Wrong out put for gmx x2top?

Dear users, I would like to simulate a zeolite structure in gromacs. I got the .cif file from IZA expanded in one direction in Materials Studio and exported a .pdb file. However, when I want to...

24 July 2024 367 4 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can a private laptop with 16GB RAM and Intel i5-1235U 1.3 GHz processor be used for WRF simulation with a 12*12 km domain?

I want to simulate WRF for a 12*12 km domain size. I want to run LSM and BSM models with a 5 minutes time interval. My laptop specification is 16GB RAM and Intel i5-1235U 1.3 GHz processor. Can I...

13 July 2024 2,037 0 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

Is there a subtle distinction between the terms "substitution" and "doping"?

Dear Prof, is there a subtle distinction between the terms "substitution" and "doping" when referring to modifying ceramic dielectric materials for example Na0.5Bi0.5TiO3? Is there any difference...

08 July 2024 2,043 3 View

What is the best software for simulation of mode locked diode laser?

Hi Dear All I would like to simulate a mode locked semiconductor laser. Does anyone know what is the best software to do it?

06 July 2024 1,648 4 View