Can I simulate surface enhanced raman scattering using ANSYS multiphysics?

05 May 2015 1 6K Report

Regarding sers biosensor, can I simulate it in ANSYS?

Very Interesting question, similar to my case. Could you check one of the spesial journal in .... (lets me check first....)

Badges
Science topic

More Rana Taha's questions See All

Can any one help me to get melting and boiling temperature of cr 39 polymer?

i need to simulate laser ablation of Allyl digycol carbonate (ADC) or cr39 and in order to do that i need boiling and melting temperature of that polymer Thsnk you

11 December 2016 1,198 0 View

How i can calculate deposition coverage area if i have deposition diameter?

If i deposit a layer of thiophenol on a gold surface,how i can calculate average coverage area if i get a circle deposit layer and i measured its radius

10 November 2016 8,095 3 View

Where i can find raman spectrometer in tehran universities ?

In any university in tehran , can i find a raman spectrometer?

07 August 2016 3,169 0 View

What is possible cell culturing application for laser induced periodic surface structure on polymer?

laser induced periodic surface structure for cell culturing

06 July 2016 5,912 1 View

Can i simulate surface enhancement raman scattering using ansys and if it is possible?

sers in ansys

09 October 2015 1,320 0 View

By using ansys,i simulated a grooves on a dielectric surface,how i can calculate surface roughness using ansys ?

how i can calculate surface roughness using ansys?

08 September 2015 6,301 1 View

By using ansys, how i can model laser heat source??

By using ansys,How i can model laser heat source??

06 July 2015 10,009 0 View

How i can simulate laser ablation by comsol multiphysics?

how i can simulate femtosecond laser ablation on a dielectric substrate using comsol multiphysics

04 May 2015 6,824 1 View

Can i simulate surface enhancement raman scattering by comsol multiphysics?

sers layer over a dielectric surface in order to get a biosensor

03 April 2015 8,367 1 View

Problems about acousto-optic coupling in Comsol, how to check whether the moving mesh is correct?

I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...

13 August 2024 9,795 0 View

Hello researchers Is this a random laser or just fluorescence?

I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.

09 August 2024 9,894 2 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

Why might the impedance values for DI water and 0.1X PBS buffer solution exhibit a decreasing and increasing trend, respectively over time (HP 4194A)?

Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...

05 August 2024 3,783 2 View

Short Synthesis of Graphene Oxide from Natural Graphite Flakes?

I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...

01 August 2024 8,368 2 View

Z-average size from Dynamic Light scattering can it be lower than the original probe size?

Hi everyone, Recently I have been conducting Dynamic Light scattering experiments in a micellar solution at 5 and gel at 37 degrees of Celsius with latex particles of diameter 190-500 nm. While...

01 August 2024 1,168 4 View

Why do some of my Raman spectra show no signal at lower Raman shifts?

I'm using a InVia Renishaw Raman microscope system (785nm wavelength, 600l/mm grating density) to acquire Raman images on human brain samples, at 50um resolution. The samples are placed on MgF2...

30 July 2024 8,771 3 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

I have synthesized a composite of ZnO and In2O3 with variations in ZnO content. In Raman , what is the peak observed at 130 cm-1?

Dear all, I have noticed, as the ZnO content increases, the Raman intensity at 100cm-1 also increases. However, there is a peak nearby at 130 cm-1, which I could not find in any paper related to...

28 July 2024 5,410 1 View