Can any one help me to get melting and boiling temperature of cr 39 polymer?

12 December 2016 0 1K Report

i need to simulate laser ablation of Allyl digycol carbonate (ADC) or cr39 and in order to do that i need boiling and melting temperature of that polymer

Thsnk you

Badges
Science topic

More Rana Taha's questions See All

How i can calculate deposition coverage area if i have deposition diameter?

If i deposit a layer of thiophenol on a gold surface,how i can calculate average coverage area if i get a circle deposit layer and i measured its radius

10 November 2016 8,095 3 View

Where i can find raman spectrometer in tehran universities ?

In any university in tehran , can i find a raman spectrometer?

07 August 2016 3,169 0 View

What is possible cell culturing application for laser induced periodic surface structure on polymer?

laser induced periodic surface structure for cell culturing

06 July 2016 5,912 1 View

Can i simulate surface enhancement raman scattering using ansys and if it is possible?

sers in ansys

09 October 2015 1,320 0 View

By using ansys,i simulated a grooves on a dielectric surface,how i can calculate surface roughness using ansys ?

how i can calculate surface roughness using ansys?

08 September 2015 6,301 1 View

By using ansys, how i can model laser heat source??

By using ansys,How i can model laser heat source??

06 July 2015 10,009 0 View

How i can simulate laser ablation by comsol multiphysics?

how i can simulate femtosecond laser ablation on a dielectric substrate using comsol multiphysics

04 May 2015 6,824 1 View

Can I simulate surface enhanced raman scattering using ANSYS multiphysics?

Regarding sers biosensor, can I simulate it in ANSYS?

04 May 2015 6,143 1 View

Can i simulate surface enhancement raman scattering by comsol multiphysics?

sers layer over a dielectric surface in order to get a biosensor

03 April 2015 8,367 1 View

Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,179 1 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Hello researchers Is this a random laser or just fluorescence?

I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.

09 August 2024 9,894 2 View

How to increase simulation box size?

We intend to study the interaction between peptides and polymer (like PP, PE and PS) through MD simulations using Martini force fields ( Martini 2 for PP and Martini 3 for PE, PS). We have...

08 August 2024 4,842 0 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Could dyes amplify the spectrum of light to a specific wavelength?

I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...

05 August 2024 3,290 1 View

When I simulate for S parameters using ADS, I have faced this issue that I have attached. Please anyone clarify me?

...

31 July 2024 1,671 3 View

How to explain the different interaction between soluble and insoluble polymer in water?

Hello everyone, I am try to understand the differences interaction between insoluble and soluble polymers in water with metal ions and how theit charge density (of metal ions) affect the interaction.

29 July 2024 6,350 3 View

Why is it not common to see similar pairs in polymer sliding pairs?

If the pairs are similar, will it reduce the adhesion due to electric charges?

29 July 2024 3,185 2 View

HAs anyone used TGA to find activation enegy of water evaporation?

I have different polymer solutions and I hypothesize that water molecules are retained based on the water-polymer interactions, so the amount of free water is less to intercat with drug tablet....

28 July 2024 9,545 6 View