I want to model an nonlinear spring element which follow an nonlinear force-displacement equation. Is there any way where I can give a nonlinear force-displacement equation as an input for the COMBIN39 element in ANSYS?
I think you can do that by designation initial gap for te element.
that is, no force will take place unless the displacement exceeds the initial gap
Use this forum
https://www.cfd-online.com/
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I isolated microbial DNA from marine water samples taken at various sites using the Qiagen Power Water DNA Isolation Kit, including a modified enzymatic lysis step. I encountered a situation where...
24 July 2024 9,688 0 View
1. Nutritional contribution of the edible coating 2. Self life of the vegetable to be coated with the edible coating. 3. Toxicity development after preserving the vegetable with the edible coating.
11 June 2024 1,740 3 View
I am using 20 mg of WO3, 800 mg of Sulphur, 925 oc growth temp, 280 oc S temp, and a 20 sccm gas flow rate.
05 May 2024 8,665 2 View
I have questions regarding the safe use of cell phones in animal research facilities. While I acknowledge the hygienic risk, we often spend a lot of time inside our barrier SPF facility and we...
14 April 2024 3,486 0 View
Ladies and Gentleman, My name is Jana Maric, and I am a tourism management student at the university of applied sciences in Germany currently researching for my bachelor´s thesis in the field of...
08 April 2024 4,449 0 View
Please do it by hand, if not possible just do by some analytic engine.
26 March 2024 2,028 0 View
I deposited Ga2O3 thin film on fused quartz substrate at 500oc in Ar ambient by RF sputtering and then annealed at 900oc (very slow heating and very slow cooling i.e 1oc/min) in air ambient for 1...
11 February 2024 3,417 4 View
ANSYS multilinear material model does not support plastic strain vs stress data with a negative slope. Moreover, it assumes perfectly plastic (horizontal) behaviour from the end data point. How...
01 February 2024 9,950 0 View
INDIAN JOURNAL OF NATURAL SCIENCES ISSN: 0976-0997 ( Print, Bimonthly ) Multidisciplinary Sciences Web of Science Indexes: Zoological Record is this journal UGC care list II category?
25 December 2023 4,017 2 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,031 2 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
Some research indicates that the fist steps toward democratization of an authoritarian regime actually lowers state capacity. How strong is the evidence for this hypothesis?
14 July 2024 8,239 3 View
I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...
13 July 2024 3,631 4 View
I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?
09 July 2024 9,226 3 View
Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."
30 June 2024 7,894 1 View
Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...
25 June 2024 4,286 4 View
I am trying the simulate the drum brake squeal in ansys. For giving the rotational velocity to drum what should i use the Rotational velocity or CMROTATE command.
24 June 2024 5,125 0 View
I need to get the eigenvalues after a modal analysis in ansys workbench. Is there any next APDL command that will get the required result.
20 June 2024 1,668 0 View