1 L tris-HCL 0.1 mol/L buffer?

Bilal Atta @Bilal_Atta

03 March 2016 1 7K Report

How can I prepare 1 L tris-HCL 0.1 mol/L buffer?

Eden Tanzosh

Weigh out 12.114g of Tris, add that to 800mL of water, use HCl to reach desired pH, and top off with water to 1 L.

Badges
Science method

More Bilal Atta's questions See All

Comparing means values by using Tukey HSD test?

Hello, I am performing statistical analysis of my research data by comparing the mean values by using Tukey HSD test. I got homogeneous group in both small and capital alphabets. This is because...

07 August 2018 6,422 9 View

Statistically analyse the research data?

Hello, I am preforming research to check the impact of different storage bags on the damage parameters of maize due to red flour beetle at different storage times. Treatments: 8 storage bags...

07 August 2018 9,021 4 View

Na2SiO3.9H2O solubility in water?

Hello everyone I want to know is Na2SiO3.9H2O soluble in only water or water+HCl. Thanks

08 September 2016 6,929 4 View

How to adjust the pH of sodium metasilicate when applied in field?

Hello everyone, I studied some research papers that soil pH will be changed after the addition of sodium metasilicate. So many of them used 0.01N H2SO4 for adjusting pH under laboratory and...

08 September 2016 2,167 3 View

Resistance investigation in wheat against wheat aphids?

Hello everyone I want to perform a prelimainary experiment for checking the resistance of six wheat varieties against wheat aphid under laboratory condition. For this I will sow 10 wheat seeds of...

07 August 2016 7,380 4 View

How I will comapre silicon concentration from 2 different field by using ANOVA?

Hello, I have selected 2 different fields for silicon determination from soil. These field are present on the same location. Two soil samples (top soil and sub soil) are taken from each field for...

07 August 2016 3,022 5 View

How I can dissolve CaSiO3 in water for applying to plants?

Hello everyone, I want to dissolve calcium silicate (CaSiO3) in water and then applied to wheat plant, but according to literature it is insoluble in water. So kindly tell me that method which...

07 August 2016 4,013 3 View

Gravimetric method for silicon determination in the soil?

Hello, I want to determine the available silicon concentration (g/kg) in the soil by using gravimetric method. Can anyone please tell me the complete procedure how to use this method?

04 May 2016 7,290 2 View

Best way for determination of aphid biology in field?

Clip cages are used in laboratories for biology determination of insects. Can anyone please tell me the best way to find out the biology of small insects like wheat aphids in the field condition?

02 March 2016 4,990 3 View

How to prepare different concentrations of calcium silicate?

I have 1 liter calcium silicate solution and want to prepare ten different concentrations of the silicate to treat wheat plants under laboratory condition by soil and foliar application. Can...

02 March 2016 9,916 4 View

AMAXA Lonza nucleofection lower volume of buffer?

Does anyone tried to do nucleofection with AMAXA by Lonza with lower than recommended amount of buffer in the cuvettes (100 ul)?

07 August 2024 4,616 0 View

Why I can't see any band in SDS-PAGE?

Currently, when I run SDS-PAGE, I don't see any bands at all, even though I used the same material just a day ago and it worked fine.... In our lab, we dilute the 10X running buffer to 1X and...

06 August 2024 5,373 2 View

Why might the impedance values for DI water and 0.1X PBS buffer solution exhibit a decreasing and increasing trend, respectively over time (HP 4194A)?

Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...

05 August 2024 3,783 2 View

What is the best blank for nanodrop if I want to read a recombinant protein concentration?

Is it the "elution buffer" or the "dialysis buffer"? Note: I'll be using NanoDrop OneC

01 August 2024 967 3 View

EDTA buffer solution?

Hello everyone! How can i prepare EDTA buffer solution (pH 8.2) to determine GSH levels? Thank you in advance.

29 July 2024 4,374 1 View

Whether i can preserve leaves samples in 2.5% glutaraldehyde in 0.05 M phosphate buffer, pH 7 for coming several weeks for further LM study ?

I want to preserve the sample leaves for the LM study of the stomata and conidia analysis. Whether 2.5% glutaraldehyde in 0.05 M phosphate buffer with pH 7 can be applied for preservation.

29 July 2024 8,560 0 View

Can a shoot-through event of a tri-state digital buffer cause momentary Hi-Z state?

// interested in the difference between floating events and short circuits.

22 July 2024 6,565 0 View

How can EDTA be removed from already extracted DNA samples?

Our lab has extracted bacterial DNA samples using Qiagen DNeasy kit and eluted the samples in AE buffer. However, this buffer contains 0.5mM EDTA not suitable for downstream application. Any ideas...

13 July 2024 1,675 3 View

How much 1X TAE buffer should I use in preparing 1.2% agarose gel?

Commonly, we prepare 1.0% of agarose gel with 0.4g agarose powder and 40ml 1X TAE buffer. if I would like to prepare a 1.2%% of agarose gel, is it I need to add 0.48g agarose powder and 120ml 1X...

12 July 2024 2,058 5 View

My Cyclic voltammetry curve doesn't show cathodic peak of Cu2+ to Cu+. how to solve this problem?

I performed CV of Cu-MOF in a buffer solution of pH 8, and we did not find any peak corresponding to Cu2+ to Cu+. What is the reason behind this? Please give your valuable suggestions.

08 July 2024 2,388 4 View