Contact experts in Mechanics of Solids to get answers
2,659 views 139 posts
Questions related to Mechanics of Solids
How can I extract the coordinates of nodes after a deformation on ANSYS and ABAQUS platform and obtain the coordinates of these points corresponding to the nodal points in the deformed body? i...
06 June 2016 3,430 3 View
Based on the equation used to calculate wave speed, the value obtained was 5.09*10^6 mm/s. The time period that used was 10 and the displacement value as displacement control was 90 mm. The...
06 June 2016 3,318 5 View
06 June 2016 8,022 3 View
In Ansys Fracture Mechanic, How tweaking the parameters (like increasing/reducing the length) of Major, Minor & Contour radius of the crack affects the J-integral? How each elements mentioned...
04 April 2016 5,399 5 View
Can anyone provide split Hopkinson pressure bar facility for high strain rate compression test of Ti6Al4V ELI in India ? i need your support in this regard.. Thanking you
18 March 2016 6,565 3 View
03 March 2016 663 4 View
As in 1-D analysis of ejector, we generally take isentropic correlations to calculate Mach no at various section of ejector. while doing the same when I take Mach no at Y-Y section(as shown in...
03 March 2016 861 2 View
1:how to model all the elements of concrete frame with BRBs using ABAQUS, the interactions between different parts, especially the interaction between the core BRB and the casing segment 2:how to...
03 March 2016 5,203 2 View
Hey all,In my thesis, I am modelling an ultrasonic standing wave that is produced from a Pz26 transducer. The ultrasonic standing wave field will be used to separate the suspended polystyrene...
03 March 2016 6,119 0 View
Black glassy phase is sintering on test specimens on stainless steel ,which is sintered with the specimens and do not come off , so we are unable to observe iron boride coatings,kindly someone...
02 February 2016 2,988 5 View
How composites can be modeled in ANSYS Using Solid185? If one try to model a fiber composite layer bonded to a concrete beam for example using solid185 element in ANSY, this layer shall be...
07 January 2016 10,060 10 View
01 January 2016 9,197 9 View
Hello, I would like to know how to create a new field output in ABAQUS viewer using an expression with the INTEGER value of SDEG damage variable of cohesive elements. Thank you in advance
24 November 2015 10,115 2 View
11 November 2015 5,697 2 View
Effect of earthquake parameters (frequency, no of cycles) on deviatoric stress under UU condition. How do the saturated clays behave differently under CONSOLIDATED UNDRAINED (CU) and...
11 November 2015 7,254 1 View
How do we know Residual strength of Concrete and Steel rebars? For example: Steel Grade 60, and Concrete f'c=28 MPa in American standard.
20 September 2015 2,057 4 View
09 September 2015 3,588 3 View
Hi, I modeled unidirectional CFRP cutting process in ABAQUS using Hashin failure criteria. Unfortunately, many researchers did not report the used fracture energies in their model. I found...
07 July 2015 5,714 11 View
Is biaxial strain apply on x and y direction? or it is different . Please anybody clear this doubt.
05 May 2015 7,843 2 View
I've been trying to get the failure parameters such as fracture toughness or fracture energy of Ammonium Perchlorate but I haven't found any source yet. Could someone assist me with one? Is it...
04 April 2015 1,523 6 View
02 April 2015 9,768 5 View
My focus is on the analysis of fracture toughness of Al-Si alloys by using a Nanoidentation. is there anyone doing this aspect ?
27 March 2015 4,902 7 View
Goal of the impact testing is to observe damage and what effects has the speed load on laminated composites. I am looking for information on layer orientation choices and impact damage tests.
03 March 2015 6,047 2 View
03 March 2015 6,935 8 View