Can anyone provide split Hopkinson pressure bar facility for high strain rate compression test of Ti6Al4V ELI in India ?
i need your support in this regard..
Thanking you
Check with Prof. P. Venkitanarayanan at IIT Kanpur.
http://home.iitk.ac.in/~venkit/
and also at IISc Bangalore (Prof. Karthik), IIT-Bombay (Prof. Krisha Jonnalagadda/Prof, Nayak), IIT-Delhi, CSIR-CGCRI Kolkatta and I am sure you will find it at many other places...
Thank you sir
you can find SHPB facility at IIT delhi(mechanical engineering) and BARC.
how to extract the values of cutting force and temperature in ABAQUS software after turning simulation?
06 July 2018 5,779 0 View
Which book/paper contains effect of turning parameters on microhardness of machined surface?
02 March 2018 5,082 0 View
how to do turning process analysis by using ABAQUS software in terms of cutting force and temperature?
02 March 2018 5,215 1 View
How to find out the simulated cutting force values from .cae file in ABAQUS ?
05 June 2017 3,888 3 View
Where is the facility for residual stress measurement in Pune or Mumbai (India)?
05 June 2017 956 1 View
Please suggest suitable software for SEM image analysis? how to give dimensions to SEM image?
04 May 2016 6,453 0 View
What are the steps for Turning simulation through ABAQUS software?
04 May 2016 7,604 0 View
03 April 2016 7,281 0 View
How to find out Johnson cook material properties?
02 March 2016 4,183 1 View
Machining simulation through ABAQUS software any consultancy available in India?
01 February 2016 1,631 4 View
Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...
02 March 2021 4,910 3 View
Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...
02 March 2021 1,999 5 View
Is there a powerful system for the security of the systems distributed on IoT systems?
02 March 2021 3,858 10 View
The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...
01 March 2021 2,272 4 View
I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...
28 February 2021 2,004 3 View
I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...
28 February 2021 6,282 9 View
I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...
28 February 2021 5,415 1 View
I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...
26 February 2021 8,183 3 View
Hi everyone, Illumina provides a list of primers to amplify with high taxonomic coverage the ITS1 region for further fungal sequencing, but I cannot find the exact amount necessary of each...
25 February 2021 6,969 3 View
Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...
25 February 2021 8,749 6 View