Contact experts in Materials Chemistry to get answers
4,088 views 1,958 posts
Questions related to Materials Chemistry
ccc
05 May 2017 4,198 4 View
how can improve the adhesion of deposited layer to poly carbonate?
05 May 2017 4,522 2 View
Jiang Yong J R Smith
05 May 2017 4,663 2 View
How to control the dye absorption during DSSC device fabrication?
05 May 2017 8,360 0 View
am working on lithium storage in ZigZag Carbon Nanotubes theoritically. for this am calculating mulliken analysis. is there any alternative
05 May 2017 2,857 2 View
a student placed a 0.1g in the Al pan and did the test at a heating rate of 9 K/min he found that the area of the melting peak was 1.2 (J/S)K if the heat of fusion of completely crystalline...
05 May 2017 6,407 2 View
looking to use urea and melamine as a coating material in combination over a polymer film layer.
05 May 2017 1,905 3 View
I need these two values for zeta potential measurements.
05 May 2017 8,356 2 View
I want to know that amongst Anhydrous Ethanol ,Acetone AR ,THF , Toluene , Which is best compatible for Hydrophobic coating based from TEOS and Amino Silane.
05 May 2017 1,429 5 View
If a gas with high concentration of H2S (30,000 ppm) has been placed in a 500 cc cylinder for one month, how much of sulfur compounds (such as H2S) are adsorbed by titanium or titanium sulfinert...
05 May 2017 1,499 1 View
I mean to that a catalyst like netural Ni.
05 May 2017 9,203 0 View
I want to make trimetallic nanoparticles of Mn-Ni-Si using chemical reduction method. I am using precursors as chlorides, for Mn and Ni it is easy to hydrate the chlorides but for SiCl4, if it is...
05 May 2017 6,045 2 View
i am trying to grow films from colloidal solution of CdTe quantum dots synthesized in aqueous media but particles do not stick with glass slides. so i am looking for binders that could be used to...
05 May 2017 6,581 4 View
PL technique requires liquid sample. Can it be used as a suspension for water insoluble materials?
05 May 2017 6,388 4 View
How can we calculate the volume fraction (f) for a diblock copolymer from its Mn, Mw, and PDI?
05 May 2017 6,433 6 View
Dear all, could you please give me information about solubility of mesoporous carbon nanoparticle
05 May 2017 3,260 3 View
The activated carbon was prepared by impregnating zinc chloride with the raw sample. I have carried out zero point charge by salt addition method and obtained a value of 7.03. Is it correct?
05 May 2017 8,489 6 View
The Temperature of KOH and Ligin should be room Temperatur around 298,15 K, Water has a fraction with room temperature and a fraction around 353,15 K, but perhaps its ok to consider all components...
05 May 2017 6,416 4 View
My professor and I were using sulfuric acid and perchloric acid with 0.2M concentration to study the quartz crystal by EQCM technique, but we could not see any changes in mass when we increased or...
05 May 2017 9,249 6 View
Affordable and simple in the sense, the experimental arrangement for the test should not be very costly and complex.
05 May 2017 9,409 6 View
Dear All, We are working on a project to investigate IMCs precipitation in AL-Zn alloys. They are primarily alpha-AlSiFe IMCs present in the temperature ranging from 575 - 610 deg C. I need your...
05 May 2017 2,998 6 View
Is there a literature, concerning CoO(OH)-quitosane hybrid composites?
05 May 2017 6,570 2 View
Hello, Could anybody give me advice how to remove blue Cu(II) complex from poly(2-hydroxyethyl methacrylate) prepared by SET-LRP? Polymerization mixture contained monomer HEMA, methyl...
05 May 2017 5,761 3 View
DIClOFENAC SODIUM shows a remarkable decrease during the successive cyclic voltammetric sweeps as in the attached picture. A decrease in the oxidation peak current occurs with an increase in the...
05 May 2017 2,984 2 View