What is use of PID controller in DC motor?

10 November 2016 8,991 0 View

Can u say the differences between IEEE and IEEE explore?

I have uploaded my paper in international conference they have mentioned that they will publish in IEEE explore

10 November 2016 6,702 6 View

Inside the petrol engine during combustion process how much temperature will be there?

10 November 2016 4,635 1 View

What is the difference between arc welding and gas welding?

basis of properties

10 November 2016 9,519 0 View

What are the parameters to be considered for modelling solar still ?

10 November 2016 2,597 3 View

Which gas is having low specific head and cost?

09 October 2016 6,558 2 View

How can i determine the efficiency of solar pond theoretically?

Solar pond

09 October 2016 4,785 8 View

How to analyze solar pond in ANSYS?

Fabricated with MS sheet with tickness of 2mm ans insulated with HDPE and themocole and salt having concentration of 35mg/litre

01 January 1970 5,664 1 View

Is glass or fesnell lens is cost effective for covering solar pond?

Solar pond will be affected by rainfall, wind etc.,

01 January 1970 642 1 View

Which material is suitable to store temperature in solar air heater?

Solar air heater

01 January 1970 9,118 2 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Help request in CST microwave?

im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...

02 March 2021 2,246 2 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Anyone found any research papers on solar furnace design calculations (for solar concentration)?

I am thinking about working on solar furnace with heliostats that concentrate sunlight and heat molten salt, but currently no luck with research. Not a lot of papers based on the subject. (check...

01 March 2021 5,023 5 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to size battery banks?

I am designing a small grid connected solar PV power-plant. As the battery's capacity is specified in Ah and demand in kWh. What is the best way to size the battery bank? I have battery price in...

28 February 2021 1,638 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View