What is use of PID controller in DC motor?

10 November 2016 8,991 0 View

Can u say the differences between IEEE and IEEE explore?

I have uploaded my paper in international conference they have mentioned that they will publish in IEEE explore

10 November 2016 6,702 6 View

Inside the petrol engine during combustion process how much temperature will be there?

10 November 2016 4,635 1 View

What are the parameters to be considered for modelling solar still ?

10 November 2016 2,597 3 View

Which gas is having low specific head and cost?

09 October 2016 6,558 2 View

How can i determine the efficiency of solar pond theoretically?

Solar pond

09 October 2016 4,785 8 View

How to analyze solar pond in ANSYS?

Fabricated with MS sheet with tickness of 2mm ans insulated with HDPE and themocole and salt having concentration of 35mg/litre

01 January 1970 5,664 1 View

Is glass or fesnell lens is cost effective for covering solar pond?

Solar pond will be affected by rainfall, wind etc.,

01 January 1970 642 1 View

Which material is suitable to store temperature in solar air heater?

Solar air heater

01 January 1970 9,118 2 View

Is there any innovation going on for solar pond researches?

Sir, Kindly notify me if there is any things

01 January 1970 2,393 1 View

Any research papers for extraction of nutrient deprivation on macroalgae? Analysed by HPLC-UV and GC/MS. Possibly from macroalgae genus Rhizoclonium?

I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...

28 February 2021 6,477 1 View

Necessary tube lenght to cool Natural gas in a dry-ice cooling bath?

I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...

27 February 2021 8,128 1 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

Why do a weight decrease for thermal degradation in nitrogen gas condition?

Hi all The question is related to TGA(Thermogravimetric analysis). Thermal degradation easily understood but why do samples weight decrease? altough just binding is broked, the weight of...

26 February 2021 1,100 5 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

What kind of steel moulds are used for hot pressing metal powders?

My main concern is that the metal powders should not weld to the mold surface and I should easily be able to eject out the pressed samples. I am looking for alternative for graphite moulds. The...

22 February 2021 2,965 4 View

Aspen Plus Error: Unknown or undefined bead number?

Hello, in my Aspen Plus Simulation (see attachment) there are two heat exchangers. One HEX1 (oil+gas) ist fed by hot gas which ist coming out of a burner. The other HEX2 (gas+gas) shall work as a...

14 February 2021 8,096 2 View

NVT or NPT is preferable for gas adsorption simulation ?

Hi there, In order to perform molecule dynamic simulation on gas adsorption on substrate materials, NVT or NPT ensemble is preferable ? Thanks!

08 February 2021 173 1 View

How can I convert permeability unit from barrer to m^2 for using COMSOL MultiPhysics?

I am looking for gas permeability of PDMS for simulation in COMSOL MultiPhysics and using creeping flow , fluid and matrix properties. The permeability unit in COMSOL is m^2 whereas I have the...

08 February 2021 4,305 2 View