How to plot upper bound and lower bound limit curves of trendline in MS Excel?

To obtain upper and lower bound curves for trendline of scattered plot.

10 May 2020 2,117 1 View

How to link user subroutine (USERFRIC) to ansys apdl?

Hello everyone, I am modelling masonry infilled RC frame in ANSYS APDL. I need to use user defined friction model (TB,matID,,,,USERFRIC). For it, I have read programmer user manual...

17 March 2020 1,705 3 View

How to control initial stiffness of global base shear vs lateral diplacement response in masonry infilled RC frame in ANSYS APDL?

Hello everyone I am modelling masonry infilled RC frame in ANSYS Mechanical APDL and defining joints (between mortar-mortar, infill and RC member) using cohesive zone material model. But the...

11 March 2020 6,403 4 View

Does keeping tissue sample (patient biopsies) in Trizol for a long time (>6 month) degrades DNA ? or Leads to sheared DNA?

I am trying to isolate RNA and DNA from the tissue biopsy stored in Trizol at -80 degree for more than 6 months . I isolated RNA using the standard Trizol method and obtained good quality and...

22 November 2018 2,446 2 View

Why are my gel pieces not getting destained for in-gel digestion?

My gel pieces are not getting destained. I have kept it for more than 6 hours now. I m using 50mM Ammonium bicarbonate and Acetonitrile in ratio of 7:3.

07 May 2018 5,419 1 View

How to properly store the sds gel pieces for in gel digestion?

I have already cut the gel pieces and would like to perform in gel digestion in future. So I had freeze them in 1% acetic acid. Can I still process those samples?

15 January 2018 1,120 1 View

Is proteomic data analysis in R (using RforProteomics) better than any other proteomic software?

My project involves analyzing proteome of my sample. I have more than 100 samples for analysis. Would proteomic analysis in R help me? Is it better than other softwares?

04 January 2018 2,591 6 View

I want reference of first paper of NiO/ZnO nanocomposites?

i want to know from were work on ZnO/NiO nanocomposite had started.

26 September 2017 3,538 3 View

What is the difference in the XRD of doped material and nanocomposites of mixed metal oxide?

25 September 2017 6,060 9 View

Howto find whether the distribution of metals in size segregated PM is unimodal, bimodal or multimodal?

06 April 2017 358 3 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

In PRIMER, is it possible to downweight certain taxa in multivariate community datasets to reflect uncertainty around identification??

I have a dataset with about 80 different species. As usual, some species are very easy to identify with certainty whereas others are more difficult, which means that I am less certain of my...

03 March 2021 8,066 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How do I increase the yield of my PCR product?

Hello, We would like to increase the yield of our PCR product. We are running a series of PCR reactions that is targeting ~1.1kb sequence. We begin each reaction with ~400pg of template DNA...

02 March 2021 4,029 3 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

What analysis to choose with a large neste dataset and clearly skewed or kurtotic distributions?

Hello! I have a dataset of n=3000 nested within 8 countries with approximately 200 or 400 responses in each country. I originally planned to perform multilevel modelling with 4 dependent variables...

02 March 2021 6,865 1 View